7MWTW1711YM0 Whirlpool Washer - Instructions

Removed the top on the agitator. Then removed the screw with a wrench. then I removed the cam and replaced each Directional cog the way they came out. Then I replaced the cam. Tightened the screw on the agitator and replaced the top. Turned the machine on and It started agitating like it was suppose to.

I popped the liquid detergent cap off of the top of the Agitator. I then removed the seal cap to expose the Agitator dog assembly and bolt. I removed the entire Agitator dog assembly and Agitator by removing the single 7/16? bolt. I pulled the old dogs out, put the new dogs in and reassembled the Agitator Assembly.

Works like new!!

disassembled two halves, cogs just sitting there, replaced, re-assembled

We took off softner cap and then took off the agitator with a nutdriver and then pulled the top off and the central agitator that the cogs were in pulled it out took the cogs out and replaced them with the new ones . Then we put the agitator back on and tightened the nut and replaced the softner cap and we were all done.

Removed the fabric cone from center of agitator pop out the plastic cover inside, remove bolt in center pull on agitator, remove cam holder and replace cams.
repeat process to re assemble

popped off the softener dispenser, pulled out seal over nut assembly, used socket wrench with extention to loosen and remove nut holding cog assembly.
slid holding ring off of the bottom (mine was black in color) pulled out old dog agitators put in new ones, reverse assembled the unit tightened it down, (be sure not to go too tight there is a rubber bushing under the nut) ran a small test load of laundry and it now works great!!!!

Took the cap off the agitator, loosened the nut with a wrench, and pulled the agitator out. The agitator pulled apart easily, revealing the piece containing the dog ears, which were clearly worn out. Simply replaced the dog ears and reinstalled the agitator. Piece of cake!

The repair was very easy, I took the top cap off the agitator and removed the recess bolt and pulled the agitator out of the washing machine,put the agitator on the floor and put my feet on the sides of the agitator and pulled the top haft apart,replaced the agitator directional cogs put back together work great

Took off softner dispenser, took off bolt cover. Used 7/16 socket with long extension and unscrewed bolt. Pulled up on agitator and out it came. Took out directional cogs and replaced with new. Reversed procedure and I was done. Saved a lot of money by not calling a mobile repair man on this one!

Removed fabric softener dispenser. Inserted screwdriver into slot on side of cover that is on agitator and pried off. Used socket extension to unscrew bolt inside agitator. Lifted out and slid off plastic ring holding agitator cogs . Replaced cogs in the same direction they came out. Since these instructions were here on site at the time I ordered the parts, it made the job very simple and fast...the order came very fast too.

First I removed the pop off cap at the top of the spiral shaped top agitator. Then reach down inside and pry off another pop off water tight cap exposing a 7/16 or 1/2 inch nut. A deep socket would probably be easiest but I didn't have one so a nut driver and luck got it unthreaded- it was pretty tight and yoiu have to hold the agitator from spinning while you unthread. Then the upper agitator asslembly lifts out and the cog assembly falls apart but it's only like 3 or four housing pieces and it only goes together one way to hold the four new cogs in place. reassemble and the machine works great again

I took out the fabric softener dispenser, then pulled of the plastic plate. There is 1 big bolt that has to be unscrewed in there. After that gets unscrewed, the whole agitator will pull out of the washer. I put the agitator on the ground, stepped gently with both feet on th bottom (mostly flat part). then I pulled on the top cylinder part, and the 2 parts separated. There is a little disk in the cylinder part that pops out. remove the top and replace the cogs. then put the disk back together. Push the two big main parts of the agitator back together...snap the disk back in and put the whole agaitator back in your washer. pop it back into place and screw in the bolt.....DONE! I have to replace these cogs about 1ce a year...it costs me about $5 and 15 minutes...but it keeps my waher running great!

Very easy repair. Popped off the top cap on the agitator with a flat head screwdriver. Then took a half inch drive socket set with the extender and removed the assembly where the cogs were housed. Inserted new cogs, put it all back together and the thing agitates like new. Simple. Saved huge dollars.

Pulled up and removed the fabric softner dispenser. Then I pulled up and removed the cap barrier to have access to the screw. Removed the screw and pulled up the cloths mover. Tunrned the cloths mover over to remove the bearing cam to remove the broken agitator cogs and replaced them with the new ones. I held the bearing cam with my right hand and held the cloths mover with my left hand turning it slowly with my left hand and lightly pushing down with my right hand until the cloths mover made contact with the grooves of the shaft and it sunk down on the shaft. Replaced the screw and washer then the cap barrier , next the fabric softner dispenser. Took 10 min. to complete the job. Now my washer runs like new ! Plus, I have a happy wife!

Removed the agitator assembly with a socket wrench and extension, replaced cogs, reinstalled assembly...took about 10 minutes because I dropped the assembly once, and had to reassemble it. An absolute "piece of cake."