7MWTW1710YM1 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dieu from Houston, TX
- Parts Used:
- WPW10006355
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
washer shake hole machine from begin spin about 11/2 ' h
chage out part and washer still shake
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Beaufort, SC
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Agitator would not agitate
Removed the agitator with a socket wrench and replaced cogs as directed in repair video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Kalkaska, MI
- Parts Used:
- WP3949550
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
agitator broke
very easy to repair , instructions very clear , parts person very good to talk to, parts got here fast
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from St. Albans, WV
- Parts Used:
- 80040
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Top part of agitator not working
I used a nut driver to remove the screw that held the to part of the agitator onto the bottom part. I then took out the worn out directional cogs and replaced them with new ones and re-assembled the agitator and was back in business. The agitator now works the way it should. Easy fix. The only negative part of this experience was that the shipping was twice as expensive as what the parts cost. Very fast shipping from PARTS SELECT .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shane from CLINTON TWP, MI
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Rinse cycle kept repeating, did not spin clothes
Spin indicator light was illuminated but machine was repeating rinse cycle rather than spinning water out of clothes. Replaced the pulley and drive coupler, thinking there was a mechanical problem. Video instructions were great but old pulley and drive coupler looked perfect so replacing them did nothing. Next I replaced the washer actuator (shifter), thinking that was the reason for no high speed spin. Easy job, as shown in the video, but it also did nothing. The problem turned out to be a failure in the control panel, probably resulting from years of vibration. Decided to stop chasing my tail and bought a new washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michele from ROCHESTER, NY
- Parts Used:
- W10780048
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
The washer was shaking during the spin cycle
Exactly like the video from the website
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Canandaigua, NY
- Parts Used:
- 80040
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Agitator stopped turning
I took a socket and removed the agitator bolt and cover which exposed the cogs. I cold see the cogs were stripped. I changed them and everything works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from WHITE BEAR LK, MN
- Parts Used:
- 80040
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench set
Agitator was skipping and seemed lose.
Removed agitator according to instructions, although upper and lower agitator did not want to separate. I used a steel rod and hammer to separate them by hitting lower agitator where bolt goes through. After removing and replacing old cogs, cog holder had to be tipped upside down to insert in agitator. I used a small dap of toothpaste to hold retainer in place while I inserted it in agitator. Works great now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from JOELTON, TN
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Taking the adjetator apart.
I went on line to find out how take the adjetator apart. You just stand on the adjetator and pull the top off. Very simple. Once that wss apart I cleaned the dog area of dirt and old pieces. Install new dogs and put it back together. I was trying to make much harder than it was. Piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jason from Barnesville, OH
- Parts Used:
- 80040
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
washer would not agitate
removed the agitator and melted the retaining clips to loosen the retainer cover for the cogs. went simple after that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from KISSIMMEE, FL
- Parts Used:
- W10780048
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Washer shaking and banging loudly during spin cycle
Replaced the suspension rods
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from BEECH ISLAND, SC
- Parts Used:
- W10780048
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Springs worn out on the suspension rods. (Noisy drum in spin cycles)
The video posted on this site will walk you right through the repair. Great service. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rodger from ANDOVER, OH
- Parts Used:
- 80040
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
top part ofagitator not turning.
Followed instructions on website video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- roger from Delanco, NJ
- Parts Used:
- WPW10072840, 80040
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
upper agitator not spinning
After removing the pressed in cap inside the agitator i removed it from the machine with a socket wrench. Then it did not take long to figure out that the two peices snapped apart. then one look at the cogs (referred to as dog ears) i knew they where stripped and where the problem. Icanceled the service call and order the parts myself from this site. So it was very easy and i'm not sure how much money i saved but the bragging rights went along way with the wife, Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Wetumpka, AL
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
worn our Agit-dogs, agitator wouldn't pull clothes down
FIRST I printed the directions from an online DIY stie, then removed a single bolt from the center of the agitator. I dismantled the agitator, replaced the dogs, and used to printed page to help me reassemble the agitator. I then replaced the bolt. It's VERY easy, but you need the pictures to be sure you've put everything back in the correct place.
Was this instruction helpful to you?
Thank you for voting!