LA5710XPW3 Whirlpool Washer - Instructions

First, I read the previous repair stories, so I knew what step to do first. So, first I took the hose off of the drain, then I removed it from the washer. And as the previous repair story stated, some water came out and I had a towel ready to catch the water that was in the hose. I threaded the clamp onto the new hose, pushed the new hose onto the washer, used the pliers to open the clamp to better clamp the hose onto the washer. Then, placed the drain hose into the drain pipe and it was done! Thanks for such a great site!

Removed the top latches with a nut driver. Removed the washing machine top. Used a nut driver to remove the valve. Used pliers to remove and replace the outlet hose clamp. Used pliers to remove and replace inlet hoses.

I have kept this washer and dryer running for 27 years now by replacing parts. I was going to replace them this time but for a $20 part they still run ok. I bet I can use the old valve for a garden irrigation project too !

A label was created and never shipped. Sat there for 2 weeks.
Contacted company for a refund and a Retha’s never been issued.
Terrible service!

Sprayed wd40 - limescale - boiling water , NOTHING WORKED after half an hour reapeted spraying and pulling the tub and shaking it back and forth - still nothing
Finally I replaced the center nut loosely than putting a piece of wood on top of it and with me holding the tub slightly high - my wife than whacked it hard several times , I also was turning the tub every whack
When it came out it was full of rust and grime - it would have never come out without what we did
Replacing the the rubber washer was easy - machine works and no more leaking- thank you for your video which really helped to start the job

1) Unplug power cable from dryer.
2) Remove the 2 screws that secure the chute for lint filter screen with
Phillips head screwdriver.
3) Remove the lint filter screen.
4) Depress plastic locking clip on each side with putty knife to release
tension and lift up top panel to clear the locking clips. Each locking
clip is located 2-1/2 inches from the front edge of side panel.
5) Lift the top panel and lean against the wall for support. If dryer top
panel cannot be raised all the way due to cabinet(s) above, tape
the dryer top panel to cabinet above or have somebody hold the
top panel for temporary support.
6) Install the new metal locking clips. Ensure that the elongated tab
of the metal locking clip is towards the front of dryer. Compress
locking clip lightly with pliers and push down into the hole.
7) Lower the dryer top panel and press it down in place over the metal
locking clips for a tight fit.
8) Reinstall the 2 screws to secure the lint filter chute.
9) Reinstall lint filter screen.
10) Reconnect power cable for dryer.
11) Turn on dryer and inspect that all dryer panels (top, sides and
front) are tight and secured.
Repair Duration: 5 minutes

Siphon break kit keeps washing machine from continuing to siphon after rinse/cycle -- like emptying a pool with a hose. Fixed the problem of the tub never filling due to siphon draining out water as it's being put in.

Removed two screws and lifted the control console then tilted forward the shell. Removed two screws holding the latch cover and assembly then disconnected two wires. I played with the assembly until I discoved the element was toast. Ordered the part but when I got it I was confused because it had three prongs (two on one side and one on the other) when the burnt one had only one and one and I only had 2 disconnect wires. I thought I had gotten the wrong part but figured it out. Actually putting the assembly together was the easy part, trying to get the outer shell back together was a little tough. Between taking it a part, figuring out what was wrong and ordering and receiving the part was about three weeks. So when putting it all together took awhile but I did it and it works great.

Used Liquid Wrench to loosen wig-wag solenoid bracket. Drilled out rivet on defective wig-wag plunger. Installed new one with easy-to-install rivet clip. Now works like a charm.

Removed the old hoses and screwed on the new hoses.

Followed instructions other customers provided for hose installation. Haven't installed agitator dogs yet. Need to watch the video on your web site.

First used wet vac to get water out. Unplug electrical cord. Shut off water and unhook lines. Unhook drain tube. Flip over on side. Take belt cover off. two screws.
Took photos of parts removing just for re- install. Ordered parts from part select.com. Came in Two days. The dealer was on 12 days I gave up on them. I removed actuator two easy screws and pulled off electrical connection no tool needed. Then removed pump three longer screws Than other part. Make sure to label them in a ziplock baggie. Plus I removed hose clamp with pliers slide Back on hose and pull hose off. Then remove electrical connection on pump. If it makes you feel better label each with masking tape so I know where each connection goes. Then replace pump first with new one. Make sure you push it in hard then the screws. Don’t over tighten. Plastic parts break. Hook back up hose slide clamp back over fitting end with pliers. Hook up wire connector. Next hook up actuator. Two screws wire connector and your done. Put belt guard back on. Socks can get caught under washer get in belt and cause major issue. Then you need to reconnect water lines. Make sure hot goes to hot. Cold to cold. Drain hose hook back up. Plug in power cord. Now the fun part. Run a diagnostic and then calibration. See you tube videos it’s like 3 clicks to left then two to right with selector knob. Write down the exact amount of clicks and steps. It works. Be sure to turn knob 4 times to left to clear it like a combination lock. Don’t let the noises scare you it makes all
Kinds of sounds while calibration goes on.

There are two screws that hold the switch in place. And two wires connected to the switch. The most difficult part of replacement is to place the new switch and hold it in place to reinstall the mounting screws. The space to work in is limited unless you remove the front panel from the dryer, which I opted not to do.

Removed broken hose and replaced with new hose. My washer will be 21 years old in January.

1. Need mop, bucket to catch leftover water in machine before you remove old hose. 2. Removed old hose by removing clamp. 3. Dried up any remaining water around fixture before attaching new hose. 4. Slide clamp to bottom of hose before attaching to machine. 5. Attached hose and clamp to machine where old hose was removed from. Make sure clamp is secure. (Please note that clamp that came with the new hose was too big. I used the old one. Worked perfectly). 6. Finally run a little water in you washer, then run out to test tightness and there is no leaks.

Move dryer away from wall. Unplug the dryer. Open the hinge top from the front edges of dryer. Remove the two screws holding the filter channel onto the top of dryer. Lean the top of dryer back away from the front . Open the dryer door, Locate switch from the top looking into the dryer top opening where you have just leaning the top back out of your way. Unplug the wire from the old switch. remove the old switch and bracket using the flat blade screwdriver for screw removal.
Place the wire on the new switch using the normally open contacts. place switch on bracket and gently position the bracket and switch over the holes designed for the switch and tighten screws using the new Phillips head screws sent with the new switch. place the top back into place and replace the filter channel screws plug in the dryer and job finished. easy as 1-2-3