GHW9150PW4 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dustin from Mount Dora, FL
- Parts Used:
- WP8181846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The door handle had cracked and broken off
First I removed the two screws that held the old handle and then replaced the new handle with the same screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lionel from HOCKLEY, TX
- Parts Used:
- WP8182233
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Baffle broke off due to drying very heavy garments.
Lined the new one up with one hand;(cold beer in the other), snapped it to place, finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Barrington, RI
- Parts Used:
- 280187
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Washer wouldn't drain
Easily. 4 Screws. 2 Clamps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benjamin from N WILKESBORO, NC
- Parts Used:
- WP8182233
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken baffle in washer.
Inserted new baffle in washer and slide in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Thousand Oaks, CA
- Parts Used:
- WP8181846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken handle
Just removed two screws with a phillips screwdriver and screwed the new handle on. Super simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maxine from Wilmington, NC
- Parts Used:
- WP8181846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door Handle broke off.
This was truely easy. All I needed was a flat head screw driver and it was done within five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Corning, NY
- Parts Used:
- 280187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
wont pump the water out
Had the old pump out - 1 screw and two hose clamp to unhook and an electrical wire to pull out - couldnt been any easier - when new one came took 5 mins to install - did a load to make sure pump worked before put it all back together
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from NEWBERG, OR
- Parts Used:
- WP8182119
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Torn bellows was leaking and eating clothes
Followed directions as shown in your repair video, having done this for the first time it took a bit longer than a repairman would have but was able to git-r-done. The most difficult part was fitting the adjustable wire back around the front of the washer, in the video it is made to look really easy however in real life it is a little more difficult and could not be attached so easily and took quite a bit of time to make sure it was attached correctly. thank you for your help.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alexander from Miami, FL
- Parts Used:
- WP8182119
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Bellow pierced
1. Remove bottom panel (3 screws below). 2. Remove top panel (3 screws back). 3. Remove detergent dispenser (remove T screw in front.) 4. Carefully remove control panel is plastic so be careful not to break it. 5. Pull broken bellow from front and spring loaded clamp will come lose. 6. Push away bellow. 7. Remove cables from door lock. 8. Remove front panel screws (4 - 2 on top and 2 in bottom). 9. Unscrew bellow's clamp with flat screw driver or not driver. 10. Remove worn bellow. 11. Bellow has notch on top (Use as reference to replace. 11. Clean all surfaces. 12. Install new bellow to drum. 13. Screw clamp over of bellow not too tight. Don't want to break the seat. 14. Replace all in the reverse order and for the front of the bellow refer to my previous article (story) on front latch replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michele from Aston, PA
- Parts Used:
- WP8181846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
handle broke off door
the old handle was held in place with two screws.
the screws were removed, handle came off right away and then the new handle was place on the door and the screws were replaced.
the screws were removed, handle came off right away and then the new handle was place on the door and the screws were replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leslie from Richmond, VA
- Parts Used:
- WP8181846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Plastic door handle broke off when caught on the pocket of my jacket
First, I unscrewed the two screws on the broken handle, using an allen wrench. Then, I screwed on the new handle in it's place. The new grey handle is much lighter in color than the original charcoal grey of the washer, but it blends well and works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carlos from TAMPA, FL
- Parts Used:
- WP8181651
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
original door hook broke in two pieces.
As easy as 123 two torx screws removed old pieces and install the new one and like that ready for another 15 years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from MORGANTOWN, PA
- Parts Used:
- WP8182119
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
The door bellows had a cut in it
I purchased a new bellows from this site I followed their instructions. Just tricky getting the inner clamp on aligned and tightened.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILLIAM from REPUBLIC, MO
- Parts Used:
- WP8182119
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Ripped bellowspul
Pull spring wire on front. Remove large hose lamp at tub. Reinstall in reverse order.
Was this instruction helpful to you?
Thank you for voting!