GHW9250ML0 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Erin from Coldwater, MS
- Parts Used:
- 285976
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Baffle broke.
The baffle just slipped on with no tools required. The best thing was that we received our parts the next day after ordering them, and we just paid for regular shipping!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carlos from TAMPA, FL
- Parts Used:
- WP8181651
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
original door hook broke in two pieces.
As easy as 123 two torx screws removed old pieces and install the new one and like that ready for another 15 years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michele from Aston, PA
- Parts Used:
- WP8181846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
handle broke off door
the old handle was held in place with two screws.
the screws were removed, handle came off right away and then the new handle was place on the door and the screws were replaced.
the screws were removed, handle came off right away and then the new handle was place on the door and the screws were replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leslie from Richmond, VA
- Parts Used:
- WP8181846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Plastic door handle broke off when caught on the pocket of my jacket
First, I unscrewed the two screws on the broken handle, using an allen wrench. Then, I screwed on the new handle in it's place. The new grey handle is much lighter in color than the original charcoal grey of the washer, but it blends well and works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Theodore from Middletown, NJ
- Parts Used:
- 8181877
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken handle
Simple. Found my torx bits, removed the screws, removed the old handle, placed the new handle in position, replaced screws.
This happened because I failed to wait for the click on the machine before I opened the door. It's a front loader and it needs time to drain the water before you open the door.
This happened because I failed to wait for the click on the machine before I opened the door. It's a front loader and it needs time to drain the water before you open the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anwar from Pleasanton, CA
- Parts Used:
- WP8181694
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench (Adjustable)
Water leaking past shut off valve (solenoid operated)
Inputs on your web site of other people who had replaced this valve assembly helped.
Remove top cover from washer - three socket head screws on rear of machine, (need to move washer forward for access)
Turn off both hot and cold manual shutoff vales on wall. Run washer to take water pressure off from hoses (turn on for water to turn on , and then turn washer off).
Remove both hoses (mark/remember which side is hot/cold, as valve assembly has no markings), from valve assembly, had to use channel locks/adjustable wrench to remove nuts as they were really tight. Check to see if gaskets were OK, would have been nice, if these gaskets are supplied with new valve assembly. Remove screw which holds valve assembly to washer. Slide valve assembly slightly side ways to free it from bulkhead panel. Remove last hose assembly inside washer, attached to valve; remove four wires from solenoids. Keep track of wires (which solenoid).
Replace valve, reconnect internal hoses and wires; install valve assemble on bulkhead panel; attach screw; reconnect hoses; turn on manual valves; check for leaks; briefly turn on washer, check for internal leaks; install cover; push back washer in place.
Remove top cover from washer - three socket head screws on rear of machine, (need to move washer forward for access)
Turn off both hot and cold manual shutoff vales on wall. Run washer to take water pressure off from hoses (turn on for water to turn on , and then turn washer off).
Remove both hoses (mark/remember which side is hot/cold, as valve assembly has no markings), from valve assembly, had to use channel locks/adjustable wrench to remove nuts as they were really tight. Check to see if gaskets were OK, would have been nice, if these gaskets are supplied with new valve assembly. Remove screw which holds valve assembly to washer. Slide valve assembly slightly side ways to free it from bulkhead panel. Remove last hose assembly inside washer, attached to valve; remove four wires from solenoids. Keep track of wires (which solenoid).
Replace valve, reconnect internal hoses and wires; install valve assemble on bulkhead panel; attach screw; reconnect hoses; turn on manual valves; check for leaks; briefly turn on washer, check for internal leaks; install cover; push back washer in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from Christiansburg, VA
- Parts Used:
- 285976
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable), Wrench set
All 3 baffles had broken
Repair was described as a simple 5 minute job following the enclosed directions. There were no directions included. Customer service replied they could not provide any instructions. I located a technical manual online and determined the steps necessary to replace the baffles. While some may just click them in, a proper repair requires the control pannel and machine housing to be removed. Then the tub assembly must be removed and the plastic tub separated from the basket. Three screws (one for each baffle must be installed. (I recommend using blue loctite to keep the screws from backing out). The entire process must then be reversed. This is a slightly complicated (note the pencil is to mark the locations of clips for ease of reinstallation. I am an Engineer and this process took over 2 hours and required a significant amount of space to lay out the parts as the machine was totally disassembled. This assembly is best accomplished with 2 people and an entire afternoon without interruption. It can be done by anyone with some mechanical skills, but find the consumer services technical manual first and be prepared to keep track of a lot of small and large parts. This is not the simple 5 minute job described by others (unless you just want to snap the baffles on the basket and not lock them down). In that case go ahead and order a few more sets as the clips will break and the baffles will slide off and you will be replacing them about every 6 months.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Big Torch Key, FL
- Parts Used:
- WP8181794
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
water inlet valve leak and hose
disconect wayer inlet hoses.remove screws that hold the top cover. This will expose the water inlet valve. remove the defective valve and any other associated clamps,hose etc. test run for leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Farmingdale, NY
- Parts Used:
- WP8181850
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
Duet Washer front bellows had a hole
Went to google; found a uTube video, plus instructions. Followed it and did the repair in a little over an hour.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- edward from ATLANTA, GA
- Parts Used:
- WP8181850
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Tears in the bellow, leaking
Follow the video when you find the part. It's spot on, exactly what you see and can expect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Kenosha, WI
- Parts Used:
- WP8181694
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
water backup when not in use, strip threads
Remove top 3 screws.
Remove 1 screw that holds inlet valve.
slide valve to the right.
Mark and remove 4 connector wires.
Reverse order to install.
Remove 1 screw that holds inlet valve.
slide valve to the right.
Mark and remove 4 connector wires.
Reverse order to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from Platte City, MO
- Parts Used:
- 8181877
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replaced handle on frontload
Removed 2 torx head screws and replaced handle
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CINDY from PASADENA, TX
- Parts Used:
- WP8181846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Handle Broke Off
I removed two screws and removed broken piece and replaced the handle with the same two screws. The color and match of the handle was perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Lexington, KY
- Parts Used:
- WP8181846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The door handle cracked
First I waited 6 days after i was E-mailed the part was shipped until it was shipped, then waited two more days to get the part!
Then i removed two TORX screws removed old handle then installed the new one in reverse order.
Then i removed two TORX screws removed old handle then installed the new one in reverse order.
Was this instruction helpful to you?
Thank you for voting!