WTW6600SW2 Whirlpool Washer - Instructions

Remove agitator and replace hub. I also recommend replacing the Suspension too. I could tell the hub was bad the piece of metal washer on the bottom was gone. The suspension lost a lot of its stiffing

Followed video from you tube. Man made it look very easy. Not! Hole that lock has to come through in back was very tricky. Also, DO NOT THROW OUT OLD PART UNTIL NEW ONE IS INSTALLED. The reason for that is there is a CLIP at the end of the old part that is needed to attach new part to wire section in control panel. NO WHERE is it mentioned at you got the clip from the old part. Luckily we saved it. Without that clip, you are screwed.

Was pretty strait forward. Took the back panel off, removed the 3 mount screws and 2 clamps on the pump, and swapped it all out. Only thing, Paid for 2 day air shipping, took a week for the part to come in. But it was still faster and cheaper then my local parts dealer.

Dismantled washer lid to install new locking mechanism.

The most difficult problem was to identify where the leak was and I tried to repair the old pump but that was a waste of my time. I was most impressed with this company in how fast the order was taken and the perfect part was shipped to me. I received the part in approx. 30 hours after I placed the order. The part was delivered by FedExpress to my front door. A very reasonable price for the part. Anyway, most anyone could have done the repair that I did without difficulty.

two small compression clamps hold the hoses in place. these are very simple to remove, however to reinstall the new hoses you should unscrew the pumps with a nut driver, secure the hoses with the clamps, and then screw the pump back to the bottom of the drum. oh yeah make sure to put the back plate back on the machine

I wasn't able to turn the washer on it's side or front, and instead had to prop it slightly up on cinder blocks due to the configuration of my laundry room. The actual repair was fairly simple, had the clamps supplied been easy to manuever, but they were not. The clamp that goes around the hose from the pump into the inlet valve wouldn't go down around the valve where it was supposed to. I had it too far up, so when I ran the washer, the whole hose popped out and flooded my laundry room. My husband suggested a better clamp, the type that actually opens and you can tighten with a screw system. $2.16 at Lowes. 2nd attempt at repair was successful, and so far no leaks. So...save yourself some time and when you get the replacement pump, take those clamps over to Lowes or Home Depot and buy a clamp that you can open fully, slip over the valve, and tighten as much as you need. If I had that type of clamp to begin with, this project would have taken an hour, tops. And by the way, I'm a 36 year old woman with NO experience fixing appliances, but plenty of experience paying other people too much money to fix things that never should have broken in the first place!

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

First replaced four basket spring supports. Next tried Basket hub assembly ( which showed wear, but not total solution). Next replaced the rotation sensor that's on the stator. That finalized the issue.

3rd time replacing this part. The plastic grooves against the metal get wore down. Only 20$ to repair ! Take off the 3/8 bolt - center pops out. Remove screws pop out old piece and tighten new piece each side evenly.

This was a very easy cure for the problem,

Removed the center cover of the agitator with a flathead. Removed the nut of the agitator main cover. Had trouble taking the cover off because of the crud holding it down I wiggled it up gently alternating n,s and e,w until I eventually saw it separating from the bottom of the basket. Once it came off you could see how nasty the old hub assembly looked. Took the screws off the old hub assembly and removed it. Matched it up with the correct new hub assembly cause the kit comes with 2. Cleaned the shaft and that general area. Installed the new hub assembly, replaced the covers. Ran the drain and spin cycle and it worked with no problem. There are videos on YouTube that show you too. DO NOT try to pry the agitator cover if it won’t rise up easily. Be patient and it will come out.

I followed the video instructions provided. However, I used the hook on an old rod to pull the new rods through the corner holes in the top of the dryer. Simple invert the old rod and feed through the hole, hook onto the new rod and lift through the hole. It enabled me to lift the tub with one hand and put the plastic seat and new rod in place with the other hand. Too easy and sped up the repair job.

Removed agitator and basket hub parts and cleaned all parts of agitator then replace basket hub with new basket hub kit according to video ran washer but did not solve problem

First I remove the 4 screws holding the lid in place using my star screwdrivers, removed the old lid, replaced it with the new one, replaced the screws and it was done.