WFW8400TW01 Whirlpool Washer - Instructions

I followed your repair video explicitly, simple fix. However, one should
be careful when disconnecting the two prong electrical connector from
the heat sensor. the two black wires can pull free easily. In that case, the
rear of the female plastic wired connector must be extracted to allow the two black wires to be "pushed" into the narrow slot which displaces the
wire insulation and allows for a good electrical connection. If a punch tool is not available a pair of needle nose pliers works. Also, observe
the orientation slots on both the male andfemale connectors - they
connect one way only! I set the washer on it's face while effecting this
repair to better see what I was doing (eyesight not as good as it used to be). Thanks for the timely support!

Replaced the pump. Continued to get the F9E1 error. Removed and cleaned the drain pipe between the drum and the pump. Problem resolved.

Unplugged washer , used shop vac to drain water through drain hose on washer. Removed both hoses from old pump. Removed electric plug, removed 2 screws from bottom of the pump. Then reverse the process.

Son-in law did the work he was finished in about 20 minutes the repair guy wanted $249.00 to take out and put in. PLUS part.

I followed the steps from online videos to determine where the leak was coming from (cleaned the pump filter, still leaking; checked gasket and inlet hoses).

Finally, I discovered a wet area and cut on the drum-to-pump hose. When I removed the hose, I found that the culprit was a credit card that had broken into shards and slit the side of the hose. I was happy to see it was from the previous owners, which meant it wasn't my fault!

I did have a hard time removing the clamps (double-wire "rotor clip" or "spring clamps", according to Google) holding the hose to the drum and pump. This became a problem when replacing the hose as well. I was not strong enough to squeeze the ends together to loosen the clamp.

Getting the old hose off was easy enough, as was putting the hose back on. The problem was clamping it back on, as I mentioned.

I tried using zip ties, but this was a disaster! I tested it using a rinse and spin cycle, and the zip tie seemed to hold. However, the hose slid off during the first full cycle I ran and dumped at least 15 gallons of water on the floor. Clean up was not fun!

My recommendation (and what I finally went with) is to use hose clamps with the small screw that lets you tighten the clamp with a screw driver. I used that on both the connection to the drum and the connection to the pump and I've had no issues since.

Overall, it's a quick fix once you have the hose replacement and the right parts. If I'd gotten the hose clamps right away, I could have been done in 30 minutes.

Hope this helps and good luck with your repairs!

This repair is something even the most casual DIY'er could accomplish. What made this even easier for me was the fact that my washer was on a pedestal so accessing the 1/4" screws were extremely easy. There is no need to tilt or lift the washer. Just open the drawer and all three screws are visible. It also made draining the water out of the washer very convenient. The video perfectly describes how to accomplish the repair and allowed me to diagnose the problem by taking off the panel, opening the trap door and allowing the water to drain into a small trashcan until all the water is removed. I could physically see that the impeller was detached from the motor and found the culprit that caused the problem - a small vile of eye drops... From there, ordered the pump, two days later, replaced it with the new and I swear the new pump must be stronger than the original because towels come out near dry after a spin cycle. Very satisfying repair!

After further investigation I realized that the original dispenser hose from the soap bin to the inner tip was the cause of the leak. Before this repair, I replaced the bellows. And as part of that replacement process you have to remove the washer dispenser hose from the inner tub so that I could complete the bellows installation. However when I put everything back together the old washer dispenser hose was leaking terribly. This was fixed easily with a new hose and an 1-1 3/4 inch hose clamp. I found an installation video that allows you to come from the top down to replace this hose but for my model of washer and because the drier was stacked on top, I took apart the front of the washer since I learned from a different video how to do this in order to install the bellows. No more leaking at all with the new hose.

Only needed a pair of pliers for the clamps on the hoses connected to the pump. Removed the old pump ( no tools needed) and reinstalled the hoses. Works like a charm!

I followed the video that accompanied the parts order confirmation. The replacement of the two parts, bellows and hose, were pretty straightforward. The job took a little less than an hour with little aggregation.

I never did the repair because Partselect.com shipped the wrong part. Then they charged me a 2nd time to resend the correct part plus the fees for shipping the correct part overnight which I did not get it until 2 days later. Now I shipped both parts back & have to wait for a refund.
I will never order from them again!

Pushed new baffles on tub clips. Pushed baffles towards the back of tub. They have been working great.

Checked for 120 V AC at pump connector. It was present . Pump was hot. Ordered new pump. Changing the pump is a piece of cake. Just tilt machine back and rest on a brick. Remove 3 5/16th screws . Disconnect 2 hoses and 1 plug. Took 10 minutes tops. Back in business.

Pretty straight forward , It is a tight work are especially laying on your stomach. To make installation easier I recommend buying a 3-4 inch hose clamp instead of trying to use the old pinch style clamp. You will only need a zip tie if you reuse the existing clamps. remember to remove the plastic ball from the old rubber hose into the new hose.

Removed top and front lower panels remove door panel.Remove ring from boot seal don’t damage seal.Replace hose,reassemble.Job is a lot easier if you purchase tool to re-install door ring seal.Tool is available from several sites on the net.

I simply followed the video instructions which was presented very clear and the video shots was on point