WTW6600SB3 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Akemi from ORLANDO, FL
- Parts Used:
- W10820048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Hard to open the washer top
Watched an instructional video many times.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clinton from IONE, OR
- Parts Used:
- W10820039
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Replace drive shaft, bearings and seal.
It is good to watch a video on how to!
Most went well, like all repairs, there are surprises, that make It take longer than expected. Once I put it back together and ran it, there was a UL code. After reading more posts, I found UL is unbalanced. After reading more… one of the problems could be the hub on the bottom may be loose. I checked that. Yep the hex bolt was loose. I forgot to put lock tight on it. Fixed that and ran it, worked flawlessly.
It would be nice to have install instructions in the box. Otherwise watch videos.
Most went well, like all repairs, there are surprises, that make It take longer than expected. Once I put it back together and ran it, there was a UL code. After reading more posts, I found UL is unbalanced. After reading more… one of the problems could be the hub on the bottom may be loose. I checked that. Yep the hex bolt was loose. I forgot to put lock tight on it. Fixed that and ran it, worked flawlessly.
It would be nice to have install instructions in the box. Otherwise watch videos.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from MEMPHIS, TN
- Parts Used:
- WP89503
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old hot water inlet hose had budge at both ends.
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James F Meehan from COARSEGOLD, CA
- Parts Used:
- W10536347, WPW10363893
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
the drain pump leaked water
fairly simple remove and put back in …I watched a video of a similar Maytag pump replace got some tips…the electoral connection is shielded by a pull up tab…so it was quite simple I got extra hose clamps in case?…didn’t need them
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Erie, PA
- Parts Used:
- W10820039
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
The agitator was making grinding noises
Removed the softener dispenser and cap that's under it. Used 7/17" socket with an 18" long extension to reach the bolt that holds agitator down. Pulled auger off, pulled lower agitator off. Removed the 6 philips head screws that hold basket hub in place. Removed hub and installed new one, replaced screws. Lightly greased spline and reinstalled lower agitator. The auger has the cam section in it. A trick to get the rollers in place is to secure them to the cam with rubber band. Have string tied to the band. Insert the cam and when almose all the way in, pull rubber band off and the rollers stay in place. Reinstalled the bolt, cap and softener dispenser.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julio from Prnceton, TX
- Parts Used:
- W10820048
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Shake and moved
At the time that I received the order part, Me and my Wife and 15 years old Douther got on it. We removed the very top of the counter and replaced once at the time every supension rod cleaned nice and neat. then we put the top on it's place conected the water hoses pluged it in and it was ready to roll.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Houston, TX
- Parts Used:
- WPW10419333
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
machine gives uneven load alarm and f51 error code
Tilt the machine over to access the bottom I rested it on a dolly.remove the rotor with an allen wrench .then rmove the 4 bolts on the stator .then lift it off the main shaft and unlug the sensor wires . just reverse the process to install the new one (be sure to allign the arrows on the sensor and the stator when reistalling. I wish i could say this solved my problem .my machine runs untill the spin cycle then it starts shaking and gives the uneven load alarm again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elijah from Point Hope, AK
- Parts Used:
- W10193886
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set, Wrench (Adjustable)
UL flashes, will not spin, really loud,& black spots under washer
We ordered the outer tub & bearing and now the washer works like it was brand new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Demopolis, AL
- Parts Used:
- W10536347
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Washer making noise down close to bottom of machine.
First unplug electrical, disconnect all hoses. If there is a large volume of water left in the machine you need to get it out.Pull machine out so you will have room to work. Lay machine front face down. Remove drive belt, inspection cover.Take the hose clamps back up the hose,remove hoses from pump. Remove the three screws that hold the pump in place.Replace pump, take steps back as you removed the pump to restore machine to operation.Total time 45 min. I am old and slow.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Delinda M from Chicago, IL
- Parts Used:
- WPW10189966
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
f1, code on the face plate of the washer,we kept on resetting it
we ordered a motor controller,pop out the old one,then replaced it with the one we ordered,and bingo,problem is solved
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joaquin from Santa Clarita, CA
- Parts Used:
- W10820048
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Washing machine was rocking a lot, and stoping too much.
Our washer wasn't really working, we called a tech to diagnose our problem, he charged us $35 to let us know that we had a suspension problem, he promised to call us back next day with the estimate for the repair, he never did. So I decide to search, I found a video showing exactly how to do it, it was a very easy, and simple process that I decide to order the parts my self. The parts were delivered to my door in 24hrs. I installed the parts in less than 45 min, and now our washer is working like new again!!!
Thanks guys.
Thanks guys.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from Verobeach, FL
- Parts Used:
- W10536347
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set, Wrench set
Won't drain the water
It was not easy but I dit my sell
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shawn from Indio, CA
- Parts Used:
- W10820048
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Washer was noisy and had a lot of movement
The rod kit fixed the issue. I cant really explain how I did it, because I dint know if I did it the right way.
Was this instruction helpful to you?
Thank you for voting!