GHW9100LQ0 Whirlpool Washer - Instructions

First, I unscrewed the two screws on the broken handle, using an allen wrench. Then, I screwed on the new handle in it's place. The new grey handle is much lighter in color than the original charcoal grey of the washer, but it blends well and works perfectly.

Simple. Found my torx bits, removed the screws, removed the old handle, placed the new handle in position, replaced screws.

This happened because I failed to wait for the click on the machine before I opened the door. It's a front loader and it needs time to drain the water before you open the door.

Inputs on your web site of other people who had replaced this valve assembly helped.
Remove top cover from washer - three socket head screws on rear of machine, (need to move washer forward for access)
Turn off both hot and cold manual shutoff vales on wall. Run washer to take water pressure off from hoses (turn on for water to turn on , and then turn washer off).
Remove both hoses (mark/remember which side is hot/cold, as valve assembly has no markings), from valve assembly, had to use channel locks/adjustable wrench to remove nuts as they were really tight. Check to see if gaskets were OK, would have been nice, if these gaskets are supplied with new valve assembly. Remove screw which holds valve assembly to washer. Slide valve assembly slightly side ways to free it from bulkhead panel. Remove last hose assembly inside washer, attached to valve; remove four wires from solenoids. Keep track of wires (which solenoid).
Replace valve, reconnect internal hoses and wires; install valve assemble on bulkhead panel; attach screw; reconnect hoses; turn on manual valves; check for leaks; briefly turn on washer, check for internal leaks; install cover; push back washer in place.

As easy as 123 two torx screws removed old pieces and install the new one and like that ready for another 15 years.

Remive 3 screws along bottom front panel and remove that by pulling down and off. Remove 4 screws from the back of washer along the top to remove top cover. Pull out dispenser tray. Remove 2 screws from along dispenser, then carefully remove the control panel by inserting a screwdriver to release internal clips along the top. Put the control panel on top of the washer. This gives you access to 2 more screws at the top, and also 2 screws on the bottom, that will release the door panel. You'll have to disconnect 3 wire connections to get access to the wide rubber gasket (bellow). There is an inner ring and an outer ring holding it in place. The outer ring is a spring. Pull that off. Then remove the inner by loosening the screw holding the clamp. Pull the bellow off and replace with the new one. Make sure the gasket goes completely over the large water spout and the smaller button sprayer at the top taking caution to have the gasket sit between the two plastic washers attached to it. Make sure the belllow is firmly seated inside and out before attaching the bellow. Reattach everything in reverse order. Problems you'll run into: getting the spring on the outer gasket as it is tight to get on and the rubber will keep slipping off the edge where it is seated. Also, you may need an extra pair of hands to hold the door up while you attach those wire connections as there is no play in the wires.

First took a picture and printed after disconnecting machine electric supply and removing top cover. removed screw holding vale in place, removed wiring .removed valve,attached wires to new valve inserted in place attached tubing and installed mounting screw and hoses, checked all again and tested

Follow the video when you find the part. It's spot on, exactly what you see and can expect.

easy process: troubleshoot problem on website-- order part--get part--watch "how to replace"video on you tube-- get it done with only a screwdriver--go out for movie and dinner with $$ saved.

Removed covers per instruction video provided by website

Go to u tube video gives instructions. Very easy to replace

Old knobs were broken, replaced with new knobs, no tools, just push new knobs on controls.

Replaced inlet valve. Took top cover off. Accessed inlet valve. Removed hoses. Replaced valve. Works like a charm.Corrected problem

Remove top 3 screws.
Remove 1 screw that holds inlet valve.
slide valve to the right.
Mark and remove 4 connector wires.

Reverse order to install.

Removed 2 torx head screws and replaced handle

Two screws. Take off old handle. Put on new handle.