CAM2761KQ0 Whirlpool Washer - Instructions

Installed part, now it works great!

Disassembled top control console and surrounding sheet metal cabinet per the video from this site. i then used a screw driver to carefully pry up each wear pad location individually and inserted the wood wedge. to about 1 1/2 inch height. rwmoved the old wear pads and popped in the new pads one by one. Closed up the unit and tested the machine . It ran like new. No more noise or viberation

I WATCHED YOUR VIDEO AND IT CHANGED OUT VERY GOOD IT WAS NOT AS HARD AS I THOUGHT IT WOULD BE. I HAD TO TAKE IT APART 3 TIMES. HE CHEWEW THE HOSES ON THE PUMP AND THE LITTLE HOSE THAT GOES TO THE WATER FILL CONTROLE. I THINK I AM A WASHER EXPERT.I AM 81 YEARS OLD SO ANYONE CAN DO IT.

The washer agitated ok, so I figured it wasn't the motor or agitator. Watching the repair videos, I assumed the clutch might be the culprit. The videos are very good, so I should have taken the machine apart and actually looked at the clutch - it wasn't too bad. Trying to put the new clutch on anyway, I noticed it didn't turn on level. I thought it wasn't seated correct, but it was then I realized the shaft was tilting. This would explain the THUMP, and the grinding must be a gear inside the transmission. As much as I hate to get a new machine, given the tremendous downturn in quality, I think that because this machine is old, it is not worth a $200 transmission. Anyone need a brand new (but test fitted so not returnable) clutch?

Removed cabinet found tub spring had worn thru rear frame, spring was also almost worn thru. Checked suspension springs very very worn at mounting points.
Ordered needed parts. All in Stock. First bracket came the next day took 5 days to get the rest 1 part at a time.
Forgot to order suspension spring clips, order them next day shipping came the next day .
Just because parts are in stock doesn't mean you will receive in a timely fashion if you need parts better order next day freight.
Videos, parts diagrams and instruction are great, regular freight is not good

I could not make the repair. If you get the pump specified on the shaft that drives the pump, the pump will be broken. I tried to call, nobody answers the phone. I ended up buying a Washing Machine and I'm stuck with a pump I cannot use.

removed water lines from back of washer. tilted washer to get access to the pump/ removed 2 hoses at pump and removed to snap clips attaching the pump. easiest repair i ever did. washer works fine now.

Repair went well and relatively easy, but did not fix the problem.
Suspect timer switch was the culprit. Nothing was clogged or plugged
up. Water pump and impeller were free and clear with no damage
or leaks.

Disconneted hoses,unplugged.removed drain hose.Turned unit on its side.Unsnapped retainers,tryed to to pull off with just my hands,that didn't work.Used a pry bar to pop off.The end of the shaft was rusted out.I took a dremel with wire brush and cleaned up the end.Then the pump njust slid on.I took it off again and applied some anti-sieze on the end of shaft.then put pump back on.Snapped the retainers and put hoses back on.It was easy.When I first looked up washer parts,I found this other site and the price ws doulbe.Then I found you guys ,1/2 the cost and it was here in 2 days.Thank You Parts select.

I am an old woman who is disabled and without any tools or knowledge, but sheer stubbornness and will power, I waited for my tools and other parts to come in, in the mean time I fixed my young neighbors whirlpool washer, well We took top off the nut I had already pre assembled her cam so set it in place of old one put bolt back in place and the top of agitator she says works perfectly now, my parts came in I had nothing to remove as my handicap daughter had already thrown away all the loose parts, I threw away old top agitator, assembled cam and put in place still did not feel tight enough so added seal from other nut!! it worked tight enough, put the inner part back in with new part and soap put the top back on and now works good as new, was disappointed could not put bottom agitator in place, just not strong enough lol well this was my story

1. Removed back panel.
2. Removed Entire control paned, control and switch units disconnecting wiring assembly from motor.
3 Tilted front and side panel assembly away from frame, tub assembly and motor transmission assembly.
4.Removed cap from top of agitator, removed bolt holding agitator. Removed agitator, this part was tricky since some corrosion on shaft made agitator very difficult to pull off.
4. From bottom of unit disconnected motor/transmission unit from wash tub.
5. Located clutch assembly and removed lock washers. Removed clutch and replaced with new one.
------------------------------------------------------------
Steps 1 thru 3 were unnecessary.
All that needed to be done was to removed the agitator assembly. then turn unit on it's side or back and removed motor and transmission from the bottom.

I removed the cabinet and agitator, layed the machine on it's back, removed the pump, motor and gearcase. I found a way to prop the gearcase up so it rested level, removed the cover, drained the old oil. I removed all internal parts, disassembled them and cleaned them. I reassembled the gearcase using the new uetral drain assembly, and replaced the oil. I made sure the brake assembly was pushed into position and then put the gearcase, motor and pump back in. I sttod the machine up, put the cabinet back on and tested the machine. It still did not spin, so it wasn't the coupler, clutch or nuetral drain assembly.

Yes, I agree that the actual replacement of the pump was an easy task on this whirlpool washing machine, however, unlike other posters, I had no access through the bottom of the machine. My machine has a solid pan on the bottom. It has a large hole in the center - I think to access the transmission, but no access where the pump is.
So, I had to dismantle the entire enclosure, first the back (about 6 screws, a couple of electrical connections, etc.), then remove the rest of the enclosure to reveal the guts of the machine. I also had to disconnect a small vacuum tube attached to the tub, and remove the control console on top along with the back. It was pretty straight forward, took about two hours to dismantle. Then, the actual removal of the pump was as easy as others have described here - two spring clips and a hose clamp and I had it in my hand. I ordered the new part, which came very quickly - 2 days I think. Then I took another two hours to re-assemble the machine. It works - yeah!
Symptoms - water leak on the floor, it was actually intermittent for a time, so I procrastinated. Then when I actually did the work, I could see the rust trail and follow it to the leaky pump. The pump was actually leaking through the center, where the drive shaft from the motor goes. There is probably a seal between the impeller and the central drive slot that gives out after a while.
New pump in - machine back together - no leaks.

The hardest part was removing the machine's cabinet. 2 screws on either end of the control panel, tip the control panel back out of the way and remove 2 clips, then slide the cabinet off the front. Replacing the valve was very easy. I didn't need the mounting plate that came with it. At first it looked like the screw hole wasn't going to line up with the hole in the back of the machine, but then I noticed that the valve had a groove that allowed it to slide downward on to the back. Pretty easy overall.

Watch the video