LA5243XYN1 Whirlpool Washer - Instructions

As I tore my ACL, my wife actually did the actual repair while I talked her through it. The video on your website was such a great help. Our repair went exactly as depicted.

Loosing back cover to reach in and remove valve

I removed the faulty valve after unplugging the AC cord. Two screws, the two water hoses were removed, and the electrical connections were unplugged. The old valve could then be rotated so that the clamp on the fill tube could be loosened and the tube pulled off the valve.
The new valve body seemed to be an exact replacement, but the mounting bracked was slightly different and required drilling two new screw-mounting holes; an easy job.
Before securing the mounting plate to the machine, the fill tube and clamp were reattached, and the electrical connectors plugged in. After connecting the supply hoses and plugging in the AC cord, the machine filled with water properly and everything seemed to be back to normal.
I might have been able to use the original mounting plate, but it had been taken to a different location which was too far away to easily retrieve.

I simply watched the video that PartSelect has online and it was a big help although my washer was a little different it still gave me the general idea on how to remove the casing. Great website! Thanks PartSelect!

This is a very easy repair. After shutting off the water, removing the feed lines, and of course unplugging the electricity, all I had to do was: 1. remove two screws 2. flip the control panel up 3.unplug a wiring connection 4. pop two clips that hold the housing to the back 5. lean housing forward 6.unplug wiring at valve 7. remove fill hose 8. remove two screws. 9. toss old valve in the recycling bin (or trash depending on your area) 10. Reverse procedure using new valve. 11. wash clothes.

replaced valve. Everything now working. Ordering the part was simple and I found a how to video on line that was great The whole replacement of the defective part was easy and the machine was back on line in 30 minutes.

I notice a screetching sound started and as time went on the water that flowed out to fill water drum was not working properly, unplugged washing machine electrical cord from outlet. disconnected water hoses, removed screws from control panel, pulled out front cover off wachine machine to access water valve, removed by unscrewing 2 screws, placed bracket on new part(placed over valve and pushed bracket up to slide and align srew to tightenbracket), put everything back in reverse order, helpfull video on video web site for visual

I replaces the water inlet valve and now I have full pressure for the cold water to fill the tub.

To Whom It May Concern:

I had issues with my washer not flowing cold water very efficiently.
I was convinced I was going to have to spend at least $200 to get
someone to fix it or buy a new unit. My friend showed me your site
and videos. I quickly found the part I needed, had full confidence
that my problem would be solved with that part and that I'd be able to
do it myself. I ordered the part yesterday, got it today, and
installed it in under 15 minutes (thanks to the excellent video).
What an amazing customer experience!!

This is the greatest buying process I've every had with an Internet
purchase....hands down!! You saved me a couple hundred bucks and made
it fun and easy for me to fix myself. You guys are the best. No
doubt about it.

Thank you so much, Jason

I found the helpful video, after a bit of a struggle removing rear panel from machine!! I determined the problem of being the water inlet valve from prior troubles on a machine.
I removed the screws from bottom of rear panel,then the Phillips screws from the back of control panel. bumping the control panel towards the front of the machine dislodges it from it's slots. the control then tilts back on plastic hinges, exposing the clips that hold on the rear panel.Those clips are pried up and removed. dis connect the wire harness to control panel. A similar screw as the first removed at bottom hold the inlet valve on the panel.. two simple wire terminals are pulled off as well as a small water line. I did not remove the entire cabinet front as shown in the video as space did not permit it. Still easily reached. the reverse was done to install. The machines are heavy, do get help there.
I did not have it. Be certain to shut off water supply before beginning. Also, I forgot to reconnect the wire harness to control panel. you wont,RIGHT.

Rmoved top, removed back, replaced valve.

I just followed the instructions from a previous customer. Worked perfectly.

I watched the video on changing the valve. Then ordered the part. The video showed exactly how to do the repair and it was so easy.

looked on the find a part by s symptom. found the part,moved the washer took off the back.took 2 screws off of the top of the machine/controls.lifted the top.replace the water inlet valve.put it back together.easy repair.

I diagnosed by reversing the plugs on the hot/cold valves. I then removed the valve , cleaned it up and sprayed the electrical contacts with (Corrosion Block) and re-assembled. It still only had hot water. Ordered part, received part next day. When I went to install it I discovered that the (Corrosion Block) had penatrated and all was working! So now I have a spare valve.