GSQ9632LW0 Whirlpool Washer - Instructions

Removed washing machine skin and pulled pump from front bottom of washer by removing input and output hoses and disengaging clips holdin pump on motor drive. Pulled pump free of motor drive. Installed new pump in reverse order.

After reading other repair stories I did it like they said. I disconnected all the hoses and drained as much water as I could. The top came apart easily with a regular screwdriver, a 1/2 in drive with extension, and a 14 or 15mm deep socket. The spanner nut came off easiest with several short, quick blows (punch and hammer, counterclockwise). In my case a good wack seemed to be soaked up by the wash tub springs. Be careful not to chip the tub.

I laid the washer, front down, onto a couple a 2x6's. I supported between the tub and body with small 2x4 scraps. The motor/trans/pump came off easily after disconnection the 2 hoses (towels handy) and wiring. After the 3 screws, and some wiggling, the assembly slid out nicely. The coupler came out after snapping the springs off to remove the pump and motor. A 1/4 nut driver and regular screwdriver assisted. Watch how the pump comes off. You might want to mark its orientation with a marker or something. Make sure you get the new coupler on all the way with some taps on the CENTER where the shaft is. Reassemble in the reverse order. You'll know why I suggested marking the water pump.

Watch the order/orientation of the springs, clips, and washer. The clips came off with a screwdriver and pliers. It's always nice to have a rag on them when removing, they like to shoot off and land in the spot that's hardest to find, like under the dryer. My clutch was assembled with the right spring and slid right on. Don't forget about the plastic washer, snap it in good. The plastic piece still on the washer was simple. I opened up a nose pliers and put it on each side of the clip then gave it a hit. It came off with minimal effort and didn't spin on the shaft like pushing on one side with a screwdriver.

During reassembly I put a very light film of grease on the shaft. That washer with the tabs gave me trouble at first. I put a good film of grease on the side with the tabs to hold it in place, with the tabs down, in the clip. Otherwise when sliding the assembly back together it comes loose and you won't get the motor/trans all the way in. Then it all has to come back out and you'll wonder what the heck is keeping the transmission from seating in all the way. You might even get it all together, figuring the motor or tub has to turn to get it to seat right. You may even try running a no clothes load and get stuck with a tub full of water. Ask me how I know.

Reverse everything to reassemble. Make sure you get the springs tight that hold the hoses on. I was worried about over tightening the plastic nut with a 1/2 drive. Run no-clothes load, large, hot with soap. I think tipping it over loosened some stuff that was stuck in between the tub and basket. No, it wasn't grease from the shaft, light film. Anyway, I'll waste a washer full of hot soapy water to avoid the, "Um..what's this on my new shirt".

I didn't mean for this to be so long winded, but I was leary about tackling this job at first. I know my way around the garage/cars, but never tried appliances before. I pictured it'd be apart for weeks and I'd have to call a repair man. Then the "I told you so" look would come. You all know what I mean. I just want to cover as much as possible and encourage others while having them avoid any troubles.

Ordered the part, received part in short time and snapped it on in less than a minute. Seals better than original.
Thanks PartSelect. I will be back.

Siphon break kit keeps washing machine from continuing to siphon after rinse/cycle -- like emptying a pool with a hose. Fixed the problem of the tub never filling due to siphon draining out water as it's being put in.

Unplugged washer. Pulled the washer away from the wall & leaned it back against the wall to access the underneath side of the washer. Disconnected water hoses to the pump with water pump pliers. Have drain pan handy to catch the water, approximately 1 qt. Remember which hose goes to the proper place. Removed two retaining screws/straps allowing the motor to be seperated from the transmission. There is enough slack in the wiring to allow you to drop the motor without disconnecting. You do not need to remove the water pump. Removed old coupling & replaced with the new one. Make sure you use the "new style" replacement coupler or you will be doing this repair again very soon! Schematics are available online.

Replaced the springs after watching the video's from this site and problem has been solved.

The coupling, made of plastic and rubber, on our Whirlpool washer gave out. Done the same repair nine years ago and knew what to do. Here is a short summery:

1. unscrew the 2 screws that hold the control panel on top of the machine in place

2. unscrew the screws that connect the housing with the back panel

3. pop the 2 clips under the control panel to release the back panel

4. with the back panel loose disconnect everything
that is pushed, screwed or clamped on and take the back panel off (don't worry about remembering where things go, everything can go only one way together again)

5. slightly lift the housing of the washer in the back to remove, that gives you access to the coupling in front of the machine

6. I personally like to put the washer on its back and do the repair that way. However, if you want to
leave it standing that is gets you there too.

7. take the screws out of the brackets that hold the pump (the thing with the two hoses attached to it)
in place and snap off the brackets; lift up the pump and put aside

8. you can now remove the broken coupling

9. check for any fragments and clean off what needs to be cleaned

10. replace the coupling

11. reverse the order of steps 1 to 7; make sure that the all electrical connections and hoses are connected!

12. test

First read up on what others did and tried to find free repair manual with little luck. Called repairman, they thought whole transmission was shot- would have been $70 just to have them look- forget it. Getting it apart: popped off the two console cosmetic panels to get to a screw on each side from the top. Lifted off console, levered and squeezed retaining clips. Unhooked two connectors and overflow tubing? Shell pulled off easily, getting back on after I was all done made me wonder if it was a good choice. In the end yes- allowed me to clean inside surfaces of both tubs to remove grime and rust. There are many stories on the actual clutch replacement, so won't go into too much detail but some lessons learned. Keep track of the way all the plastic aggitator pieces go in, plus the washers and clips along the way. Deep well 1/2" I think socket for the tub, it's litely spring loaded so look before you set it down. Punching off the nut on the tub worried me, but it was no big deal. Loosens and tightens the normal directions, no positive tight stop, just compression so pay attention to how tight and hard you pounded to get it off. Drain the water from the inner tub before getting too far. I took the four springs off and removed both tubs to clean. No more complaining about brown spots on clothes. Get the whole clutch kit, not just the band, even though it's probably just the band worn out. The plastic clutch engaging piece will probably be fatigued. The motor etc is heavy, and buffered it's drop with rags. tip on side when putting it back, because its a bear to try to lift up. I lightly greased some moving parts, just not much as to not cause band grip problems. The wire retaining clip is tricky- I put the hook end in first, used pliers to try and compress, and screwdriver to push down and in. The whole things wants to spin while you do this, but when it finally goes, it stays. I was concerned about the location of the band spring in relation to it's actuator when putting it together, but it turned out if you put it anywhere where the clutch is free to spin, it will engage normally. The top lid has two rubber bumpers, one fell off and landed on the front bottom corner of the cover which didn't help reinstallaion until my 8year old noticed it! Took a number of tries but finally got the four guides from the frame into the cover. I tried bringing it in level, front tipped sligthly up, front tipped slightly down; in the end I won't be much help, it just finally went. It wasn't as easy as most people said it would be, but my back hurt and I had kids "help", and it took just under two hours. Works amazingly well now. Parts arrived Two days after ordering, with no expiditing!

I just replaced the spring just like the vid show me.it run's like a new one-I bought it used about 5 yr's ago

Clutch was noticibly worn compared to new part. Direct drive flange had broken, this part should be steel. found a you tube video that was simple to follow. no problems

replace clutcher

I first took the 2 screws out and disconnected the wires, I got my parts ordered and when they came in I put it back together then plugged th wires back in. I really could not believe that I could do something of this nature but when I started it was easy. My boyfriend wanted to take the washer to a repair shop, but I said first I will take a look and see if it will be worth saving. Otherwise I will junk it. It cost me with shipping costs 41.00 I am very proud of my self.
But I read other peoples experience on fixing the same problem that I had so I gave it a try.
I will not hesitate to do other jobs myself. Doreen Finlaw

Disconnected power, all hoses. Tilted washer backward to see underneath. (Placed sturdy 6" high object under back of washer to keep it from going flat on ground and possibly damaging hose connects). Looked for area where motor and transmission connect. Saw broken part (coupling). After trial and error, figured out how to remove pump and then motor, by removing strap type holding clips, and then broken part was accessible. Ordered part online and was easy to install and reassemble washer now that I knew how it came apart. If I had known the part name or number beforehand, I could have watched the replacement instruction video on this site, but I figured it out anyway, and I did it without removing the whole control switch panel and side panels/body of washer, like they do in the video. But..I guess they had to do that to give you a good view of all the parts and things they were removing underside. I recommend watching video for this part install,so you see what needs to be removed and how underneath, but then just tilting washer back to access underside, without all that control panel and sides removal.

researched the problem from the web-site.found the three most common things that would cause the problem.inspected the washer to see if there was evidence that one of the described parts had falled,and found that the tub wear pads were missing do to wear.simply replaced and it solved the problem. Thanks for the information.

The tough part was replacing the front cabinet.
I did consult the video for help on replacing the clutch spring.
Thank you for that bit.

I admit to taking too much apart, most of the cabinet back can be left alone.
Some of the plastic wire keepers/routers suffered, as well as the console hinges.

The newly reassembled washer works without a hitch, and truely it took me about 4 hours over several days to dissamble and reassemble.
It is louder in the audible range than before, but very serviceale for another 20 years, saints willing.