WFW8500SR01 Whirlpool Washer - Instructions

The removal of the bellows was easy and quick. The instructional video was really good. Only one problem with video. The step of removing the console from washer leaves out that there is a center screw in the center of console. I almost broke the console. It took took a long time in getting bellows on interior area due to tight finger space. Wire gasket fairly easy. The outer gasket after getting door and latch on. Whew! That was a bear. Video looked easy. I finally had to get help to get it on. The reason was that every time I thought I had it, the bellows would roll off will the wire gasket. A screw type as the inner area would make it so much easier. Shipping. Kudos to your company. I was expecting that I would be without washer for a week. I ordered on a Friday and it was here early Monday morning. That was amazing. By the way I did this except the outer wire gasket by myself. I finally had to get "husband" to help with that. Thanks Parts Select! If the need arises that I need another part. You will be my go to company.

A previous person had broken the actuator switch connection so I replace it and got rid of the error code. But water poured out and I eventually took off the whole dispenser assembly and found a sock had stopped the big hose up where it enters the outer wash drum.

Perfect part...saved me hundreds on labor. Thanks!

Put towel down to catch excess water, opened drain screen, used pliers to remove squeeze clamps on both hoses, removed front hold-down torx-head bolt and slid pump assembly out. Compared new part to old and found 2 differences 1:no hold-down location in front for bolt,2: the rubber padded feet are not the same. I was able to remove the two screws on the right side and use just the rubber pad for support while sliding the left side in the slot and is was plenty stable and works just fine. I guess the Whirlpool Duet model is a bit different on mounting but everything else fit quite well, the washer is working perfectly again.

Unplug Unit, remove lower cover screws with screwdriver that has 1/4 drive at end, put 2 gallon bucket at strainer remove water. Remove inlet hose clamp and outlet hose clamp, disconnect pump motor wiring plug, aggressive push to RIGHT popped right out. put a dab of Vaseline on new units rubber base slide back in reverse order. Plugged in check for leaks put back together, Repair took less than 15 minutes, working great! WHAT I FOUND IN STRAINER: LEGO'S-CHANGE-PAPER CLIPS, enough things to destroy the impeller !

took the old part out by the front panel and put the new pump in and now it works great. only took a couple of minute to put the new one in. thank you for saving my washer.

unplug washer from outlet carefully tilt back to get at underside of washer remove bottom panel. pump location lower right front. remove two hoses from back using pliers keep note on hose location. remove two bolts on underside of machine slide pump to the right to release from rubber holders to install reverse the process also good idea to use the new hose clamps that come with your new pump and the rubber mounts if they are included

The only issue I had was getting the hose from the tub re-installed, but that was my fault, the pump went right in. It couldn't have been easier. I was very pleased, received the replacement pump in just a couple of days, packaged very well for shipping, and had it installed in a matter of minutes. It took longer to take off front panel to access pump than it did to install it. Very pleased with "Part Select".....will use again!

Had my appliance man do it. It was the first one he had ever done in 20 years of working on Whirlpool. It was quick. The parts I received from you were cheaper than his supplier. Needless to say that made me very happy!

Replaced the pump assembly. The different type of clamp supplied in the kit was very helpful.

First unplug the washer. Make sure and drain washer completely. If not drained remove front panel , Remove 2.5 inch Plastic drain cover which has a catch bin on it. This will allow it to drain the washer. Put pan underneath to catch the water. Tip washer back and prop up with something 6 inches tall to get to the screws underneath. A cement block would work well. Use pliers to squeeze hose clamp together to remove the Hoses. Gently lift up The flip down cover Over the top of the wire harness Push in the tab on the wire harness, Gently pull back on the wire harness. Remove two mountings screws from the bottom of the washer. Slide the whole pump housing to the right and Lift up. Now the pump is been removed. Inspect inside the hoses For Debrie. Remove anything that is left in the hoses. Reinstall the pump in reverse order from the way you took it off. Leave front panel off Make sure all hoses and wire harness are hooked up. Run wash cycle to make sure there are no leaks. Do not put hands in while running. If no leaks replace front panel. Not sure if this is the right way But this is the way we did it and it worked well. Washer runs quieter now than it did when we got it

We purchased a new pump and installed it very easily. My washer works great!

I removed the service door and rear access panel to get at the bolts on the shocks and removed them one at a time. I did notice that the replacement shocks were heavier duty than the originals but was not an install problem. The machine is good as new now. A note, an appliance company wanted 800 to 1000dollars to diagnose and repair problem,i was able to do the repair myself for 70 dollars

I watched the video and it really was as easy as it looks. Great shipping time, I ordered the pump Monday and it arrived on Thursday, standard ground shipping!

I removed the three bottom screws and removed the plate. Removed the control panel, removed the star screw on the left side and pulled off the front panel of the machine. Loosen the bellow clamp with a phillips head and pull off the front spring clamp on the bellow. Pull off the old bellow and re installed the new one. Installed and tightened the bellow clamp and spring loaded clamp on the front of the bellow and re installed the panel, and control panel. Checked for leaks.