GHW9100LW1 Whirlpool Washer - Instructions

UNPLUG WASHER ,SLIDE WASHER OUT FROM THE WALL. TAKE THE BACK OFF ,THEN TAKE PANET OFF IN THE FRONT. TWIST OLD SHOCKS ON THE TOP FIRST THEN TWIST BOTTOMS AND THE SHOCK WILL CUM OUT. PUT NEW SHOCK IN BOTTOM FIRST TWIST TILL YOU HEAR OR FEEL THE SHOCK SEAT ITSELF THEN INSTALL ON THE BOTOOM OF THE TUB.

Factory hose clamps were awkward to maneuver. I used automotive radiator hose clamps instead. They worked great.

Just removed two screws with a phillips screwdriver and screwed the new handle on. Super simple

Remove three screws on bottom panel lift up and remove panel.The water pump in right in front. One screw holds it in place and the input and output hoses are on the back side.The hose clamps are a little hard to take off I found that before taking the one screw off the pump remove these two lines.Putting the pump back in secure the pump with the one screw. The output line is easy the intake line can be a bit of a more work to get it on because the rubber is so thin.Getting this hose and clamp was tough. Most of all use a wet vac to remove water in washer and vac out the line to drain doing this will be water free during replacing water pump.Run a cycle to make sure the lins do not leak. The other is the people that has posted this replacement are very good

This was truely easy. All I needed was a flat head screw driver and it was done within five minutes.

Removed old parts and installed the new parts.

First I removed the two screws that held the old handle and then replaced the new handle with the same screws.

Had the old pump out - 1 screw and two hose clamp to unhook and an electrical wire to pull out - couldnt been any easier - when new one came took 5 mins to install - did a load to make sure pump worked before put it all back together

Easily. 4 Screws. 2 Clamps.

Exact fit VERY GOOD Quality would order any part
again

I had units stacked so I had to take the dryer off, pull 3 screws from back, slide cover back and the water valve is right there, easy to change. I have not had the problem since then.

Inputs on your web site of other people who had replaced this valve assembly helped.
Remove top cover from washer - three socket head screws on rear of machine, (need to move washer forward for access)
Turn off both hot and cold manual shutoff vales on wall. Run washer to take water pressure off from hoses (turn on for water to turn on , and then turn washer off).
Remove both hoses (mark/remember which side is hot/cold, as valve assembly has no markings), from valve assembly, had to use channel locks/adjustable wrench to remove nuts as they were really tight. Check to see if gaskets were OK, would have been nice, if these gaskets are supplied with new valve assembly. Remove screw which holds valve assembly to washer. Slide valve assembly slightly side ways to free it from bulkhead panel. Remove last hose assembly inside washer, attached to valve; remove four wires from solenoids. Keep track of wires (which solenoid).
Replace valve, reconnect internal hoses and wires; install valve assemble on bulkhead panel; attach screw; reconnect hoses; turn on manual valves; check for leaks; briefly turn on washer, check for internal leaks; install cover; push back washer in place.

Repair was described as a simple 5 minute job following the enclosed directions. There were no directions included. Customer service replied they could not provide any instructions. I located a technical manual online and determined the steps necessary to replace the baffles. While some may just click them in, a proper repair requires the control pannel and machine housing to be removed. Then the tub assembly must be removed and the plastic tub separated from the basket. Three screws (one for each baffle must be installed. (I recommend using blue loctite to keep the screws from backing out). The entire process must then be reversed. This is a slightly complicated (note the pencil is to mark the locations of clips for ease of reinstallation. I am an Engineer and this process took over 2 hours and required a significant amount of space to lay out the parts as the machine was totally disassembled. This assembly is best accomplished with 2 people and an entire afternoon without interruption. It can be done by anyone with some mechanical skills, but find the consumer services technical manual first and be prepared to keep track of a lot of small and large parts. This is not the simple 5 minute job described by others (unless you just want to snap the baffles on the basket and not lock them down). In that case go ahead and order a few more sets as the clips will break and the baffles will slide off and you will be replacing them about every 6 months.

The baffle just slipped on with no tools required. The best thing was that we received our parts the next day after ordering them, and we just paid for regular shipping!

the old handle was held in place with two screws.
the screws were removed, handle came off right away and then the new handle was place on the door and the screws were replaced.