WTW5025SW0 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gifford from North Richland Hills, TX
- Parts Used:
- W10793634
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The original part became clogged with softener glop and partially broke while attempting to clean.
Merely pulled the old part out and put the in new one. Fit perfectly and is working fine.
Was this instruction helpful to you?
Thank you for voting!
Tub was banging the right sidewall violently.
Bought this unit sight unseen with the dryer for $100 bucks. Would not finish a spin cycle. Ordered the suspension rod kit and a new absorption pad for the inside wall.
Removed 2 screws from the back.
Opened lid.
Removed plastic tub shroud.
Reached in and disconnected 1 suspension rod by hand.
Replaced it. Used the hook end of the old rod to help pull the new one into place.
Repeated for the 3 others.
Cleaned inner wall on right side with alchohol and rag. Replaced absorption pad.
Replaced tub shroud.
Replaced lid and put screws back.
Tested with load of towels.
Problem solved.
Removed 2 screws from the back.
Opened lid.
Removed plastic tub shroud.
Reached in and disconnected 1 suspension rod by hand.
Replaced it. Used the hook end of the old rod to help pull the new one into place.
Repeated for the 3 others.
Cleaned inner wall on right side with alchohol and rag. Replaced absorption pad.
Replaced tub shroud.
Replaced lid and put screws back.
Tested with load of towels.
Problem solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Tulsa, OK
- Parts Used:
- W11130362
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Violent banging during spin cycle
Installing the new suspensions rods fixed the problem. The video was easy to follow along with!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gordon from CHESAPEAKE, VA
- Parts Used:
- W11130362
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Hard get my arm down beside the drum.
First: watch several DIY videos. They are great. I would add one thing. There's one corner that's really tight. If you remove the opposite diagonal shock first and leave it out while you replace the tight one, it gives you more room to reach down beside the drum.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from INDEPENDENCE, KY
- Parts Used:
- W10752187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
the impellar mechanism wore out so stopped aggitating
Popped the cap , used a socket to unscrew the bolt (it was stripped so ended up having to cut off bolt) Took off old impellar and replaced, installed a new bolt, replaced Cap and it was fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Blaine, WA
- Parts Used:
- W10721967
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Making groaning noise in spin
Having been out of the business for quite a few years I thought that I was dealing with a direct drive machine. Thinking that it was the motor coupler. I removed the control panel and attempted to pull the cabinet froward. Not so, it had a solid cabinet, so I tilted the machine against the wall and looked under the washer finding the driven Transmission pulley loose on the shaft. The splines on the pulley were pretty well worn but I tightened the nut and it worked okay. But I ordered a pulley and replaced after it's arrival. The motor capacitor also broke it's mount off so I had to rehang it with zip ties and repaired the wires to the Capacitor, (Which BTW had about 22 gauge wire). I found it hard to believe that they would use such small wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from DREXEL HILL, PA
- Parts Used:
- W11244231
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Replace drain hose
At first I had to position the washer so I could get access.. after having it positioned, I figured it out. Getting the clamp fastened, I was done.
Was this instruction helpful to you?
Thank you for voting!