GHW9100LQ1 Whirlpool Washer - Instructions

Repair was described as a simple 5 minute job following the enclosed directions. There were no directions included. Customer service replied they could not provide any instructions. I located a technical manual online and determined the steps necessary to replace the baffles. While some may just click them in, a proper repair requires the control pannel and machine housing to be removed. Then the tub assembly must be removed and the plastic tub separated from the basket. Three screws (one for each baffle must be installed. (I recommend using blue loctite to keep the screws from backing out). The entire process must then be reversed. This is a slightly complicated (note the pencil is to mark the locations of clips for ease of reinstallation. I am an Engineer and this process took over 2 hours and required a significant amount of space to lay out the parts as the machine was totally disassembled. This assembly is best accomplished with 2 people and an entire afternoon without interruption. It can be done by anyone with some mechanical skills, but find the consumer services technical manual first and be prepared to keep track of a lot of small and large parts. This is not the simple 5 minute job described by others (unless you just want to snap the baffles on the basket and not lock them down). In that case go ahead and order a few more sets as the clips will break and the baffles will slide off and you will be replacing them about every 6 months.

The baffle just slipped on with no tools required. The best thing was that we received our parts the next day after ordering them, and we just paid for regular shipping!

the old handle was held in place with two screws.
the screws were removed, handle came off right away and then the new handle was place on the door and the screws were replaced.

First, I unscrewed the two screws on the broken handle, using an allen wrench. Then, I screwed on the new handle in it's place. The new grey handle is much lighter in color than the original charcoal grey of the washer, but it blends well and works perfectly.

Simple. Found my torx bits, removed the screws, removed the old handle, placed the new handle in position, replaced screws.

This happened because I failed to wait for the click on the machine before I opened the door. It's a front loader and it needs time to drain the water before you open the door.

As easy as 123 two torx screws removed old pieces and install the new one and like that ready for another 15 years.

Remive 3 screws along bottom front panel and remove that by pulling down and off. Remove 4 screws from the back of washer along the top to remove top cover. Pull out dispenser tray. Remove 2 screws from along dispenser, then carefully remove the control panel by inserting a screwdriver to release internal clips along the top. Put the control panel on top of the washer. This gives you access to 2 more screws at the top, and also 2 screws on the bottom, that will release the door panel. You'll have to disconnect 3 wire connections to get access to the wide rubber gasket (bellow). There is an inner ring and an outer ring holding it in place. The outer ring is a spring. Pull that off. Then remove the inner by loosening the screw holding the clamp. Pull the bellow off and replace with the new one. Make sure the gasket goes completely over the large water spout and the smaller button sprayer at the top taking caution to have the gasket sit between the two plastic washers attached to it. Make sure the belllow is firmly seated inside and out before attaching the bellow. Reattach everything in reverse order. Problems you'll run into: getting the spring on the outer gasket as it is tight to get on and the rubber will keep slipping off the edge where it is seated. Also, you may need an extra pair of hands to hold the door up while you attach those wire connections as there is no play in the wires.

First took a picture and printed after disconnecting machine electric supply and removing top cover. removed screw holding vale in place, removed wiring .removed valve,attached wires to new valve inserted in place attached tubing and installed mounting screw and hoses, checked all again and tested

Removed covers per instruction video provided by website

easy process: troubleshoot problem on website-- order part--get part--watch "how to replace"video on you tube-- get it done with only a screwdriver--go out for movie and dinner with $$ saved.

Follow the video when you find the part. It's spot on, exactly what you see and can expect.

Old knobs were broken, replaced with new knobs, no tools, just push new knobs on controls.

Go to u tube video gives instructions. Very easy to replace

Remove top 3 screws.
Remove 1 screw that holds inlet valve.
slide valve to the right.
Mark and remove 4 connector wires.

Reverse order to install.

Removed 2 torx head screws and replaced handle