WTW6200SW0 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Clinton from IONE, OR
- Parts Used:
- W10820039
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Replace drive shaft, bearings and seal.
It is good to watch a video on how to!
Most went well, like all repairs, there are surprises, that make It take longer than expected. Once I put it back together and ran it, there was a UL code. After reading more posts, I found UL is unbalanced. After reading more… one of the problems could be the hub on the bottom may be loose. I checked that. Yep the hex bolt was loose. I forgot to put lock tight on it. Fixed that and ran it, worked flawlessly.
It would be nice to have install instructions in the box. Otherwise watch videos.
Most went well, like all repairs, there are surprises, that make It take longer than expected. Once I put it back together and ran it, there was a UL code. After reading more posts, I found UL is unbalanced. After reading more… one of the problems could be the hub on the bottom may be loose. I checked that. Yep the hex bolt was loose. I forgot to put lock tight on it. Fixed that and ran it, worked flawlessly.
It would be nice to have install instructions in the box. Otherwise watch videos.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James F Meehan from COARSEGOLD, CA
- Parts Used:
- W10536347, WPW10363893
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
the drain pump leaked water
fairly simple remove and put back in …I watched a video of a similar Maytag pump replace got some tips…the electoral connection is shielded by a pull up tab…so it was quite simple I got extra hose clamps in case?…didn’t need them
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from MEMPHIS, TN
- Parts Used:
- WP89503
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old hot water inlet hose had budge at both ends.
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Erie, PA
- Parts Used:
- W10820039
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
The agitator was making grinding noises
Removed the softener dispenser and cap that's under it. Used 7/17" socket with an 18" long extension to reach the bolt that holds agitator down. Pulled auger off, pulled lower agitator off. Removed the 6 philips head screws that hold basket hub in place. Removed hub and installed new one, replaced screws. Lightly greased spline and reinstalled lower agitator. The auger has the cam section in it. A trick to get the rollers in place is to secure them to the cam with rubber band. Have string tied to the band. Insert the cam and when almose all the way in, pull rubber band off and the rollers stay in place. Reinstalled the bolt, cap and softener dispenser.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Veronica L from Junction City, KS
- Parts Used:
- WPW10072840
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The seal in the upper agitator cap broke
I just unscrewed the top agitator cap and slid the o-ring on and put it back. Done in seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Colfax, WI
- Parts Used:
- WPW10072840
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace a seal
Just had to remove cap on agitator and replace new rubber seal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bonnie from Baytown, TX
- Parts Used:
- WPW10189966
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Every wash cycle would throw out the "F1" code and I would have to keep changing the wash cycles until one would finally catch. Replaced Motor Control Board and now works excellent!
Read the previous reviews and showed my son the diagram which he then replaced the part in about 15 minutes. No more hassle and works like a charm :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brett from seymour, IN
- Parts Used:
- W10820048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
replace suspension rods
took top off.2.replaced rods one at a time.placed top back on.very simple.evan got new bushings for the top.very simple process.no skills required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Demopolis, AL
- Parts Used:
- W10536347
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Washer making noise down close to bottom of machine.
First unplug electrical, disconnect all hoses. If there is a large volume of water left in the machine you need to get it out.Pull machine out so you will have room to work. Lay machine front face down. Remove drive belt, inspection cover.Take the hose clamps back up the hose,remove hoses from pump. Remove the three screws that hold the pump in place.Replace pump, take steps back as you removed the pump to restore machine to operation.Total time 45 min. I am old and slow.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- axel from lighthouse point, FL
- Parts Used:
- W10820048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
drum made loud noise
put machine on side pushed old rods out to top installed new ones. runs like new. tried to ask mechanics or stores nobody would help with info, they all want to send mechanics with 80$ just to get here. it was easy to do. thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Josh from Lodi, CA
- Parts Used:
- W10820048
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
vigoirously shaking causung UL code
Replaced rods with new set of 4
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from New Milford, NJ
- Parts Used:
- WPW10074580
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The seal was broken on the agitator cap barrier
Removed the fabric softner at the top of the agitator (needed a screw driver to pry it loose) and reached in to grab the barrier with my hand and pulled it out, very simple to do.When I put the new one in I put some liquid soap on the gasket and it snapped right into place.Very easy to do, all is well now, thanks Part Select.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Sandy Springs, GA
- Parts Used:
- WPW10072840
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lots of gunk between fabric softener dispenser and where it attaches to the agitator
Rubber O ring around the Inner Cap was rotted and busted through. Replaced with new Inner Cap Seal. Easy as pie!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorraine from Millsboro, DE
- Parts Used:
- WPW10072840
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken seal
went well but alas the problem still exists.
Was this instruction helpful to you?
Thank you for voting!