GHW9300PW3 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- RICHARD from Portland, OR
- Parts Used:
- WP8182119
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Old bellow pulled loose and torn
Was able to remove old bellow without dis-assembly. Replacement required removing the front of the machine for access. Once the front was off, the bellow was simple to replace. Biggest difficulty is getting the top mark on the bellow lined up. It has a tendency to slip out of position while you are working the back of the bellow over the retaining lip and it is not possible to rotate the bellow after it is installed. Fortunately, the tube from the detergent tray can be rotated slightly to allow for a small amount of error. Replacing the front retaining wire and spring required three hands at one point, but was otherwise not a problem. Fortunately removal and replacement of the front of the machine is pretty straight forward. I needed to disconnect wires to set the front out of the way, but it is impossible to plug them back in incorrectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Sonoma, CA
- Parts Used:
- WP8182634
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
door latch error code
removed all the panels to change the door latch switch
plug in three plugs ...works great
Thank you
plug in three plugs ...works great
Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from Patterson, CA
- Parts Used:
- WP8182233
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
baffle in tub fasteners broke, baffle disconnected from tub
This part slides in and snaps in place, a 15 second job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MIKE from BENBROOK, TX
- Parts Used:
- WP8182233
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Baffle in washer tub broke off
Snaped new one in place and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from Branford, CT
- Parts Used:
- 280187
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Clothes came out dripping wet
Just removed the bottom cover to access the water pump. Drained the water through the filter housing. One screw and two hose clamps and the pump was out. Installed new pump and checked for leaks. None found so the cover was secured in plase. Great news, WIFE is happy.
Was this instruction helpful to you?
Thank you for voting!
Door would not open.
It takes 2 people to do this repair.The bellow is the hardest part. One person has to hold the bellow in one spot, and the other person has to put it on the rim of the drum all the way around. Sort of like putting a tire on a bicycle. Dont do what I did and pry the door open. If you do that you will have to get a new door lock control at $54.Take off the lower front panel and reach up to the manual releace tab on the right side and pull down. Please make sure that the power is turned off, unplug the washer from the wall for your safety. The door switch itself is easy to replace, 3 screws, 3 plugs. Hope this helps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from DERIDDER, LA
- Parts Used:
- WP8182634
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The washer was unable to run without door locking
Removed the washer tub gasket and then removed the door part that I order . It was real easy to replace it and the tub gasket . Took about 8 min to complete everything .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Tempe, AZ
- Parts Used:
- WP8181859
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The knob that controls the wash setting broke
It only took a few seconds to slide on the new knob after it arrived by UPS. The part arrived sooner than scheduled. Great service and product.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Valerie from Huxley, IA
- Parts Used:
- WP8182119
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Leaked water
simple repair. After reading other reviews my husband was confident he too could do the repair. He was right, we were so very glad not to have had to call for service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ramon from Houston, TX
- Parts Used:
- WP8182119
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Front seal leaked
It was so easy my wife replaced the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Chanute, KS
- Parts Used:
- WP8181859
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Control Knob Broke
I removed the old control knob by pulling it off and installed the new one. Your service was great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Adrian, MI
- Parts Used:
- 280187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Shaft in water pump broke
I removed the one screw that holds pun
mp in place. I pulled to the left and foward about an inch to remove hoses and unplug wire. then pulled pump assembly out. The new one went right in. The wire plug went right in without any customizing. I think this was about as easy as it gets.
mp in place. I pulled to the left and foward about an inch to remove hoses and unplug wire. then pulled pump assembly out. The new one went right in. The wire plug went right in without any customizing. I think this was about as easy as it gets.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Virginia Beach, VA
- Parts Used:
- 280187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Washer would not drain.
Removed three screws holding the cover, then one screw holding the pump assembly in place. After unplugging the power, it took two minutes to remove the clamp-rings from the hoses. The reverse was equally idiot-proof! But THIS "idiot" had 10-thumbs which added to the time to replace the lock rings! Added an extra 5 minutes at most! _grin_
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jill from New Rochelle, NY
- Parts Used:
- 280187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The water didn't drain, so the drum wouldn't spin
I took off the cover, removed one screw. Removed two hoses and the electrical connector. It only 5 minutes to replace the old pump with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wilfredo vega from STRATFORD, CT
- Parts Used:
- W10822553
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Drum was out of balance
Easy fix,
I remove the front lower panel and the shocks where right in front of you , with a little twist with an adjustable wrench the cam right off . I removed and the replaced and it the same when you remove the back panel.
P.S when installing the shocks start by connecting to the bottom and then connect to the drum it will make it lot easier.
Good luck on your repair
I remove the front lower panel and the shocks where right in front of you , with a little twist with an adjustable wrench the cam right off . I removed and the replaced and it the same when you remove the back panel.
P.S when installing the shocks start by connecting to the bottom and then connect to the drum it will make it lot easier.
Good luck on your repair
Was this instruction helpful to you?
Thank you for voting!