WFW9400SW00 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- wilfredo vega from STRATFORD, CT
- Parts Used:
- W10822553
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Drum was out of balance
Easy fix,
I remove the front lower panel and the shocks where right in front of you , with a little twist with an adjustable wrench the cam right off . I removed and the replaced and it the same when you remove the back panel.
P.S when installing the shocks start by connecting to the bottom and then connect to the drum it will make it lot easier.
Good luck on your repair
I remove the front lower panel and the shocks where right in front of you , with a little twist with an adjustable wrench the cam right off . I removed and the replaced and it the same when you remove the back panel.
P.S when installing the shocks start by connecting to the bottom and then connect to the drum it will make it lot easier.
Good luck on your repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gustavo from YOUNGSTOWN, OH
- Parts Used:
- WP8183202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Door was not closing properly, broken swivel arm under hinge.
removed door from washer, set flat on table and just loosen up the screws all around, removed old hinge and replaced with new hinge, very easy. back to washing clothes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from NASHUA, NH
- Parts Used:
- WP89503
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Leaking water inlet hoses.
Removed the old hoses and screwed on the new hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from SAN MARCOS, TX
- Parts Used:
- WP8540015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Multiple water leaks, all rubber parts are chewed up from a mouse 1/
1/4 inch nutdriver, took the top and the front panel of and renew all rubber parts / hoses. It looks less than 1 hours. All parts like factory quality, everything fits perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Kotzebue, AK
- Parts Used:
- 280187
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Pump not draining the water out.
First I made sure the washer was unplugged from the outlet and I took out 3 screws that held the front panel and removed it to get access to the pump.
I disconnected the electrical plug to the pump and there were 3 phillips head screws that held the pump in place that needed to removed. Pulled out the old pump and slide the new one in it's place with no prorblems. Tighten the 3 screws on and plugged it back in and away we went washing clothes again.
I disconnected the electrical plug to the pump and there were 3 phillips head screws that held the pump in place that needed to removed. Pulled out the old pump and slide the new one in it's place with no prorblems. Tighten the 3 screws on and plugged it back in and away we went washing clothes again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gopaul from Queens, NY
- Parts Used:
- WP8182119
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Bellow was damaged,water leakage.
First,we took apart the front of the washer and then we removed the old bellow and put the new one on.After we put back up the front of the washer and open the door to put the clamp on then after we unlocked it.After it was working good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Avis from Abingdon,, VA
- Parts Used:
- WPW10156617
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plastic retainer ears broke
Took old broken part off and replaced with new. Involved removing 2 screws and putting back.easy repair. Biggest problem was length of time it took part to arrive.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- claude van from big sandy, TN
- Parts Used:
- WPW10388414
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
tub would not turn
take the back cover off and put belt on. the belt is a tight fit and requires sone effort, but can be done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from AUSTIN, TX
- Parts Used:
- WP8182862
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The inlet valve begins to restrict water flow into the washer based on normal calcium buildup. At a certain point, the washer will start giving an F20 error code indicating it is not getting enough water.
This is a straightforward replacement. Move the washer to an area where you can work on it. Unplug the washer from the wall. Turn off the water and disconnect the hot and cold water hoses at the washer. Remove the back of the washer. Slide out the top of the washer. Remove the small hose from the valve to the remainder of the washer. Disconnect the two control wires to the valve. Replace the valve. Replace the small water hose. Reconnect the wires. Replace the top and back of the washer. Connect the water back up. Plug in and try a test load. The water should flow fast enough to reach the back of the machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from JACKSONVILLE, FL
- Parts Used:
- WP8183202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Broken hinge
Removed door from washer, remove hinge from door. Then slip in hinge and tighten hinge to door. Then attach door. It works and the most important thing the wife is happy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Day from Basking Ridge, NJ
- Parts Used:
- WP8182233
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Baffle was worn out/broken
No instructions needed. Very easy to replace. You guys are great! Much cheaper than others and delivered next day! You are now on my "favorites"!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Douglas, AL
- Parts Used:
- WP8182119
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Replace Bellows between door and tub
Remove top and front
Care taken to unplug door wiring
should have taken notes or photos where srews go and order
remove old bellows large hose clamp and sping tensioned clip
clean surfaces
install new bellows on tub only
put all panels and door together
Connecting wiring to door and strain relief takes 2 people
connect bellows to door with spring clip
Care taken to unplug door wiring
should have taken notes or photos where srews go and order
remove old bellows large hose clamp and sping tensioned clip
clean surfaces
install new bellows on tub only
put all panels and door together
Connecting wiring to door and strain relief takes 2 people
connect bellows to door with spring clip
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darrell from Lady Lake, FL
- Parts Used:
- 280187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Pump not working
Replaced pump
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from YARDLEY, PA
- Parts Used:
- WPW10110225, WP8182862
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
Inlet valve was stuck in open position allowing washer to fill with water when not in use.
Removed lid. Took old parts off and replaced with new parts. Also replaced hoses while washer was moved away from wall.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Francisco from DELTONA, FL
- Parts Used:
- WP8182862
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Tub filling when power was off due to inlet valve leak.
Followed instructions as shown on repair video at site.
Was this instruction helpful to you?
Thank you for voting!