MVW6200KW4 Whirlpool Washer - Instructions

I followed the instructions provided by the video which I thought were spot on. Even to the size of the phillips screw driver.

Tightened up the pulley as the video showed me that might be the issue.

I put the dial to drain and and pressed the pause button for 3 seconds and it drained.
Unplugged the washer from the electrical outlet .
Shut the hot and cold water off. Disconnected and drained them.
Placed the washer on a soft mat on front side exposing the back and bottom of the machine.
Unscrew the metal cover with Philips head screw driver.
Disconnect the drain hose to a bucket or small dish tub .
Remove the belt cover with 5/8 ratchet or wrench.
Using a ratchet or wrench remove the one bolt holding the clutch in place .
Remove the two Philips head screws from the shift mechanism ( looks like clock timer,my memory is failing me right now sorry! ) .
Pull down on bottom gear after removing nut.
Push in and pull down with a flat head screwdriver on the tabs holding the collar in place above the top gear .The collar and gear and spring should come apart.
Install new parts in the same order . Reassemble make sure to use Locktite 242 on the bottom nut holding the gear.
Install belt , belt guard , cover drain hose . Stand machine back up , reconnect all hoses tightly plug machine into electrical outlet and start. Put a smile on your face because you did a great job and saved yourself some money!

Watch video on the site and the insulation will be easy and take about 30 min.

Followed detailed instructions which were supplied with the parts. It was easy and my machine is working great with no issues. Also I just didn’t get the main drive pulley, all new parts came for the bottom end, great service and excellent parts.

First used wet vac to get water out. Unplug electrical cord. Shut off water and unhook lines. Unhook drain tube. Flip over on side. Take belt cover off. two screws.
Took photos of parts removing just for re- install. Ordered parts from part select.com. Came in Two days. The dealer was on 12 days I gave up on them. I removed actuator two easy screws and pulled off electrical connection no tool needed. Then removed pump three longer screws Than other part. Make sure to label them in a ziplock baggie. Plus I removed hose clamp with pliers slide Back on hose and pull hose off. Then remove electrical connection on pump. If it makes you feel better label each with masking tape so I know where each connection goes. Then replace pump first with new one. Make sure you push it in hard then the screws. Don’t over tighten. Plastic parts break. Hook back up hose slide clamp back over fitting end with pliers. Hook up wire connector. Next hook up actuator. Two screws wire connector and your done. Put belt guard back on. Socks can get caught under washer get in belt and cause major issue. Then you need to reconnect water lines. Make sure hot goes to hot. Cold to cold. Drain hose hook back up. Plug in power cord. Now the fun part. Run a diagnostic and then calibration. See you tube videos it’s like 3 clicks to left then two to right with selector knob. Write down the exact amount of clicks and steps. It works. Be sure to turn knob 4 times to left to clear it like a combination lock. Don’t let the noises scare you it makes all
Kinds of sounds while calibration goes on.

It was really easy after watching the videio. I removed a single screw and took the agitator out, You could see how worn the center of the part was. The part that it went onto had a lot of rust built up on it, I used naval jelly and a wire brush to clean it. then put the new agitator on. It has been working well ever since. What's crazy is two repair men told me to
throw out the washer because the repair would be equivalent to buying a new one! NOT TRUE ---- Total cost $115.00. Received it really quickly. Thanks so much!

Once we put the washer on it's side noticed lots of oil on the floor and in the belt cover area. Replaced belt anyway but issue is the leaking transmission. Starting warranty process since Maytag carries a 10-year part warranty and machine is 6.5 years old. Wish me luck !!!

Removed two screws to remove guard. Two screws to remove another part with wires. Pulley nut was already missing. Component was twist locking tabs.

First, this is the second time the transmission actuator went bad. The first-time washer was still under warrenty and I watched the tech replace it. This time warranty has expired and I'm mechanically inclined, so I ordered the part. Replacing was easy, unplug, tip washer up so you can get under it, remove plastic guard (two hex nuts) and remove actuator by removing two screws. Reverse procedure to install new actuator. The only caution I will say is when tipping washer if you have a wall to lean it against, perfect, just put something under it for saftey so it can't fall on you.

Ordered drain hose extender. It uses a rubber flange with hose clip to attach to washer's plastic hose. When tightened, the hose clip crushes the plastic hose and crimps it, causing a leak. My solution was to find a copper pipe flange that was the same diameter as the interior of the plastic hose to act as a bushing for the plastic hose. The hose clip could then be tightened without deforming the hose. Worked great with no leaks.

Tip the washer on its back remove the agitator install new one under 15 minutes

Took the Cover off and installed belt.

Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.

I turned off and disconnected the water lines (have a bucket ready) and tipped the washer on its back. I followed along with the provided video that was super helpful. Disconnecting, moving the washer, and reconnecting everything took longer than the repair. Very satisfied with this repair!