GHW9300PW1 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Eric from Vacaville, CA
- Parts Used:
- WP8182119
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Bellow leaking water
Removed the outer spring with pliers. Pushed the bellow into the drum. Loosened the clamp on the bellow with a stub nose screwdriver. Removed the bellow. lined bellow up with soap fiting. Reversed procedure to reinstall.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Barrington, RI
- Parts Used:
- 280187
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Washer wouldn't drain
Easily. 4 Screws. 2 Clamps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lionel from HOCKLEY, TX
- Parts Used:
- WP8182233
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Baffle broke off due to drying very heavy garments.
Lined the new one up with one hand;(cold beer in the other), snapped it to place, finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maxine from Wilmington, NC
- Parts Used:
- WP8181846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door Handle broke off.
This was truely easy. All I needed was a flat head screw driver and it was done within five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dustin from Mount Dora, FL
- Parts Used:
- WP8181846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The door handle had cracked and broken off
First I removed the two screws that held the old handle and then replaced the new handle with the same screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Bothell, WA
- Parts Used:
- WP8182703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Washer had a 'thunk' sound during washing. I removed the back and saw the broken shock.
1. After ordering I watched the video on the page for the part, the guy showed exactly what to do.
2. The day the part was to arrive I leaned the washer back and opened the lower front, based on the video on the page for the part, and removed the old shock absorber.
3. Part arrived, and I put in the new shock.
4. I ran a light load in the washer and it worked.
5. I put the washer back together and put in place.
6. I have since run a full load and it has worked well.
Note: In case I messed up the shock I was putting in, I bought 2 but did not need the 2nd one. I have kept it, just in case my 20 year old Whirlpool might need another one in the future.
2. The day the part was to arrive I leaned the washer back and opened the lower front, based on the video on the page for the part, and removed the old shock absorber.
3. Part arrived, and I put in the new shock.
4. I ran a light load in the washer and it worked.
5. I put the washer back together and put in place.
6. I have since run a full load and it has worked well.
Note: In case I messed up the shock I was putting in, I bought 2 but did not need the 2nd one. I have kept it, just in case my 20 year old Whirlpool might need another one in the future.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from VIRGINIA BCH, VA
- Parts Used:
- WPW10467289
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Replacing the heat sensor following an F-24 Error Notice.
I followed your repair video explicitly, simple fix. However, one should
be careful when disconnecting the two prong electrical connector from
the heat sensor. the two black wires can pull free easily. In that case, the
rear of the female plastic wired connector must be extracted to allow the two black wires to be "pushed" into the narrow slot which displaces the
wire insulation and allows for a good electrical connection. If a punch tool is not available a pair of needle nose pliers works. Also, observe
the orientation slots on both the male andfemale connectors - they
connect one way only! I set the washer on it's face while effecting this
repair to better see what I was doing (eyesight not as good as it used to be). Thanks for the timely support!
be careful when disconnecting the two prong electrical connector from
the heat sensor. the two black wires can pull free easily. In that case, the
rear of the female plastic wired connector must be extracted to allow the two black wires to be "pushed" into the narrow slot which displaces the
wire insulation and allows for a good electrical connection. If a punch tool is not available a pair of needle nose pliers works. Also, observe
the orientation slots on both the male andfemale connectors - they
connect one way only! I set the washer on it's face while effecting this
repair to better see what I was doing (eyesight not as good as it used to be). Thanks for the timely support!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kirk from P C BEACH, FL
- Parts Used:
- WP8182703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Tub would get out of balance on the spin cycle
UNPLUG WASHER ,SLIDE WASHER OUT FROM THE WALL. TAKE THE BACK OFF ,THEN TAKE PANET OFF IN THE FRONT. TWIST OLD SHOCKS ON THE TOP FIRST THEN TWIST BOTTOMS AND THE SHOCK WILL CUM OUT. PUT NEW SHOCK IN BOTTOM FIRST TWIST TILL YOU HEAR OR FEEL THE SHOCK SEAT ITSELF THEN INSTALL ON THE BOTOOM OF THE TUB.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Thornton, CO
- Parts Used:
- WP8181694
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
tub filling with water when not in use
I had units stacked so I had to take the dryer off, pull 3 screws from back, slide cover back and the water valve is right there, easy to change. I have not had the problem since then.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carlos from TAMPA, FL
- Parts Used:
- WP8181651
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
original door hook broke in two pieces.
As easy as 123 two torx screws removed old pieces and install the new one and like that ready for another 15 years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michele from Aston, PA
- Parts Used:
- WP8181846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
handle broke off door
the old handle was held in place with two screws.
the screws were removed, handle came off right away and then the new handle was place on the door and the screws were replaced.
the screws were removed, handle came off right away and then the new handle was place on the door and the screws were replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leslie from Richmond, VA
- Parts Used:
- WP8181846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Plastic door handle broke off when caught on the pocket of my jacket
First, I unscrewed the two screws on the broken handle, using an allen wrench. Then, I screwed on the new handle in it's place. The new grey handle is much lighter in color than the original charcoal grey of the washer, but it blends well and works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sean from Palm Coast, FL
- Parts Used:
- WP8182119
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Tear in door seal
First I removed the retainer ring that holds the outside bellows on the frame of the front washer.
I then pushed the bellows inside of the drum of the washing machine in-order to get to the clamp that holds the bellows on the inside of the drum. To pull the clump I had to use a stubby screwdriver and socket drive to loosen the clamp. Once the clamp is loosen I was able to pull the bellows off, of the drum and out of the washing machine. Installation was the reverse of removal.
I then pushed the bellows inside of the drum of the washing machine in-order to get to the clamp that holds the bellows on the inside of the drum. To pull the clump I had to use a stubby screwdriver and socket drive to loosen the clamp. Once the clamp is loosen I was able to pull the bellows off, of the drum and out of the washing machine. Installation was the reverse of removal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jim from winchester, VA
- Parts Used:
- WP8182119
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
front door leaking
2 clamps and its off, problem is if you have average size hands you will struggle in getting the back clamp on and off.
Was this instruction helpful to you?
Thank you for voting!