7MGHW9400PW2 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Frank from WEST WINDSOR, NJ
- Parts Used:
- WP8182862
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Water slowly filling the wash drum and spilling out front of machine
Water was slowly filling the wash tub and spilling out front of machine. Cause was the water inlet valve solenoid was not fully closing.
Turn off water to the machine
Unplug machine
Pull machine away from the wall
Remove the water inlet hoses.
At the back-top of the machine remove the three screws holding the top on.
Lift up top from the rear and remove it.
Disconnect the hose connected to the water inlet valve.
On the outside of the back panel remove the screw holding the water inlet valve.
Remove the water inlet valve.
Reverse the process to install the new valve
NOTE: in my case the hold in the back panel did not line up with the hole in the new water inlet valve. I drilled another hole.
Turn off water to the machine
Unplug machine
Pull machine away from the wall
Remove the water inlet hoses.
At the back-top of the machine remove the three screws holding the top on.
Lift up top from the rear and remove it.
Disconnect the hose connected to the water inlet valve.
On the outside of the back panel remove the screw holding the water inlet valve.
Remove the water inlet valve.
Reverse the process to install the new valve
NOTE: in my case the hold in the back panel did not line up with the hole in the new water inlet valve. I drilled another hole.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from LEXINGTON, SC
- Parts Used:
- 280187
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Error codes SUD and Fo2
Remove three screws on bottom panel lift up and remove panel.The water pump in right in front. One screw holds it in place and the input and output hoses are on the back side.The hose clamps are a little hard to take off I found that before taking the one screw off the pump remove these two lines.Putting the pump back in secure the pump with the one screw. The output line is easy the intake line can be a bit of a more work to get it on because the rubber is so thin.Getting this hose and clamp was tough. Most of all use a wet vac to remove water in washer and vac out the line to drain doing this will be water free during replacing water pump.Run a cycle to make sure the lins do not leak. The other is the people that has posted this replacement are very good
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Oceana, WV
- Parts Used:
- WP8182862
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Water filling up in drum when not in use
Took top off with nut driver, disconnected 2 wires , removed one screw holding inlet value. Then I reversed the procedure putting new one on. Maybe 20 min. Of course unplug power and turn off water supplies before starting the job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lionel from HOCKLEY, TX
- Parts Used:
- WP8182233
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Baffle broke off due to drying very heavy garments.
Lined the new one up with one hand;(cold beer in the other), snapped it to place, finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dustin from Mount Dora, FL
- Parts Used:
- WP8181846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The door handle had cracked and broken off
First I removed the two screws that held the old handle and then replaced the new handle with the same screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Barrington, RI
- Parts Used:
- 280187
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Washer wouldn't drain
Easily. 4 Screws. 2 Clamps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from CHERRY VALLEY, IL
- Parts Used:
- WP8182862
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Water leaking in to tub when off
Replaced faulty part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benjamin from N WILKESBORO, NC
- Parts Used:
- WP8182233
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken baffle in washer.
Inserted new baffle in washer and slide in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Thousand Oaks, CA
- Parts Used:
- WP8181846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken handle
Just removed two screws with a phillips screwdriver and screwed the new handle on. Super simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maxine from Wilmington, NC
- Parts Used:
- WP8181846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door Handle broke off.
This was truely easy. All I needed was a flat head screw driver and it was done within five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Corning, NY
- Parts Used:
- 280187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
wont pump the water out
Had the old pump out - 1 screw and two hose clamp to unhook and an electrical wire to pull out - couldnt been any easier - when new one came took 5 mins to install - did a load to make sure pump worked before put it all back together
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from NEWBERG, OR
- Parts Used:
- WP8182119
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Torn bellows was leaking and eating clothes
Followed directions as shown in your repair video, having done this for the first time it took a bit longer than a repairman would have but was able to git-r-done. The most difficult part was fitting the adjustable wire back around the front of the washer, in the video it is made to look really easy however in real life it is a little more difficult and could not be attached so easily and took quite a bit of time to make sure it was attached correctly. thank you for your help.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leslie from Richmond, VA
- Parts Used:
- WP8181846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Plastic door handle broke off when caught on the pocket of my jacket
First, I unscrewed the two screws on the broken handle, using an allen wrench. Then, I screwed on the new handle in it's place. The new grey handle is much lighter in color than the original charcoal grey of the washer, but it blends well and works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michele from Aston, PA
- Parts Used:
- WP8181846
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
handle broke off door
the old handle was held in place with two screws.
the screws were removed, handle came off right away and then the new handle was place on the door and the screws were replaced.
the screws were removed, handle came off right away and then the new handle was place on the door and the screws were replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carlos from TAMPA, FL
- Parts Used:
- WP8181651
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
original door hook broke in two pieces.
As easy as 123 two torx screws removed old pieces and install the new one and like that ready for another 15 years.
Was this instruction helpful to you?
Thank you for voting!