MHN30PDCWW0 Whirlpool Washer - Instructions

took the old part out by the front panel and put the new pump in and now it works great. only took a couple of minute to put the new one in. thank you for saving my washer.

First, I watched the video again just to make sure I had a firm grasp of the task ahead. I gathered up the tools and proceeded to begin. First obstacle: getting the washer tilted back enough to put the blocks under the front feet. The washer was sitting inside a square water pan with a drain connected directly under the middle of the washer. Therefore, the water pan did not move and I could only get the washer moved out far enough to 'barely' put the blocks underneath. Second obstacle: a clump of hair had gathered at the bottom portion of the door unnoticed and caused a slow leak from the bellows. This leak dripped down and rusted out two of the three screws. I had to use a socket set to get the screws out. Third obstacle: getting the pump removed from the bottom of the washer. With the drip, the pump had stuck to the bottom of the washer. Trying hard not to get cut on the sheet metal bottom, I pushed and pushed and pulled until finally the pump let loose. From that point on..smooth sailing just like the video. Washer fixed!

The only issue I had was getting the hose from the tub re-installed, but that was my fault, the pump went right in. It couldn't have been easier. I was very pleased, received the replacement pump in just a couple of days, packaged very well for shipping, and had it installed in a matter of minutes. It took longer to take off front panel to access pump than it did to install it. Very pleased with "Part Select".....will use again!

Perfect part...saved me hundreds on labor. Thanks!

First thing, unpluged the washer. I removed the lower front acces panal. I then propped the washer up on 2 pint sized paint cans to reach the pump mounting screws. I disconnected the wire bundle going to the pump. Then removed the inlet and outlet hoses from the pump. Then I removed the 2 mounting screws on bottom and slide the pump to the left and removed. I then pump the new pump on the same way I took the old one off, but in reverse. Easy and fast the worst part was the price of the pump.

Took less than 5 minutes to replace, So Happy;-)

open the front bottom panel (3) screws. remove panel. twist off old shocks by turning the shock counter clockwise. reinstall shock by turning clockwise.

After unplugging the washer, the unit was pulled forward and tipped backwards, I placed a 2x4 under the washer to serve as a brace. I removed the existing bolts holding the old pump in place, removed the spring hose clams, unplugged the pump and removed the damaged part. inserted the new drain pump, re-inserted the bolts and tightened them, replaced the spring clamps with "regular" hose clamps supplied with the replacement part, plugged in the power supply, removed the brace, pushed back the unit and plugged it into the outlet. From start to finish - about 20 minutes. Was running wash about a half hour after I started.

I pulled the front load washer away from the wall and unplugged. I tilted it back against the wall. I removed three screws from the lower front cover plate of washer. Once removed, I had access to the tub to pump hose which I found a small hole in. I went online to Partselect and found my part. The hose was connected in three different places by compression clamps. I then pulled the compression clamps off the connections. Cleaned up all connection points with a damp rag. Upon installation of the new tub to pump hose, I discarded the compression clamps and installed the new part using radiator clamps purchased at a auto parts store. Plugged washer back in and started a load too make sure all connections were good and tight with no leaks. After checking for leaks, I re-installed the front cover plate. Tilted washer back down being careful not too set it down hard or on my feet. Job Done....

Very --simple remove front acess panel -- open sump clean out remove water out of existing pump an hoses with small wet dry vac -- remove small wire harnes --cut band clamp on discharge with side cutter --remove inlet -suction side of pump hose clamp with channel locks --un bolt two screws on bottom side of washer with 5/16 nut runner --discard old pump reinstall new one in reverse order --only takes about 20 mins total !!! ---

I was already very familiar with the motor & drain pump, as I had disassembled my original one in attempt to find the problem & fix it. Finally, I broke down & purchased a new one. It was VERY easy to install! The most difficulty was finding the right sized board to put underneath & raise the machine up (with the dryer attached to the top of it) to place the board underneath so that I could tighten the bolts from underneath to attach the pump. After that was over, the rest was cake! Just attach the hoses & the electrical, which just clips in place & my washer is like new again! Yay! Oh, and yes, I'm a woman DIY'er.

Followed instructions from a You Tube video. I'd recently lost my job and money is tight and I thought we could save money doing it myself. By watching the video and ordering parts from you we were able to save $500 between parts and labor. Thanks

First unplug the washer. Make sure and drain washer completely. If not drained remove front panel , Remove 2.5 inch Plastic drain cover which has a catch bin on it. This will allow it to drain the washer. Put pan underneath to catch the water. Tip washer back and prop up with something 6 inches tall to get to the screws underneath. A cement block would work well. Use pliers to squeeze hose clamp together to remove the Hoses. Gently lift up The flip down cover Over the top of the wire harness Push in the tab on the wire harness, Gently pull back on the wire harness. Remove two mountings screws from the bottom of the washer. Slide the whole pump housing to the right and Lift up. Now the pump is been removed. Inspect inside the hoses For Debrie. Remove anything that is left in the hoses. Reinstall the pump in reverse order from the way you took it off. Leave front panel off Make sure all hoses and wire harness are hooked up. Run wash cycle to make sure there are no leaks. Do not put hands in while running. If no leaks replace front panel. Not sure if this is the right way But this is the way we did it and it worked well. Washer runs quieter now than it did when we got it

We purchased a new pump and installed it very easily. My washer works great!

I watched the video and it really was as easy as it looks. Great shipping time, I ordered the pump Monday and it arrived on Thursday, standard ground shipping!