ITW4880HW2 Whirlpool Washer - Instructions

slipped the new drain hose on and with locking plyers slipped the wire clap in place after three trys

Force the thin nylon strap around and down into the perimeter of the agitator. Draw it snug to the center. The strap must be long enough to make a complete loop up to the top of the tub. Insert a fairly stout wooden stick through the loop so that an upward prying motion of the stick applies a vertical force on the agitator. While the force is applied pound on the lower part of the agitator so that it will break it free from the motor's axel. Of course remove the center bolt first after removing the small hub cover.
Applying liquids to the connection did not help. Just a steady upward force and a few rubber hammer blows to the lower part of the agitator di the trick.

First had to take the top of the agitator off to expose the bolt down at the bottom of the agitator. Take a ratchet with 2 1/2 extensions to get bolt off had problems so I had to use impact gun. pull agitator straight up, was stuck a little bit, but once she giving her a few tugs, it popped off the hub. On top of the hub, there is a keyway. Use a straight screwdriver and tap it out sideways. Then remove six Phillips screws and the hub pulls out. Clean the splines really good before you put new hub in. Slide new hub in put six screws in. Tighten them down evenly. Put new keyway back in slide agitator back onto shaft. Bolt on,tighten down Bolt, put top agitator back on. Replacing shift actuator tilt washer up so you can get to the bottom side take a nut driver. There’s two screws on the shield remove them that exposes the shift actuator on the side of the transmission. Remove the harness there’s a clip you push and pull straight out and there’s two screws I believe they’re Phillips And it pulls straight down put new one up in there put the two screws back in make sure the plastic tab on the shift actuator went into the tab of the transmission replaced the wire harness, push it back in make sure it snaps in put shield back on,the two screws in,and you are ready. Once you have those parts back on, you have to reset the washer instructions in your manual. It tells you how to do it. you have to do this or your washer will not work properly.

I watched the repair video on Partselect, it was very informative. In the video the agitator lifted right out easily, I was not so lucky. It took me and another gentleman about 4 hours to get the thing out. I watched other videos on ideas to remove, still no luck. Finally I cut the strap off of a carry all bag and was able to get it in around the agitator and slide it under it. After getting it under the agitator we were able to pull up on it and get it loose.
The rest of the repair was simple, cleaned everything, installed new part, and now washing machine is working like new again.

My spin cycle was running, but spinning slowly and not drying my clothes. The agitator spun quickly like normal, but the basket did not spin fast. It seemed like something was slipping. I checked the belt, but it seemed fine and it was less than a year old. I was afraid that the transmission was going, but there wasn't any grinding sound of gears. Luckily the hub part description said that this could fix the slow Spin cycle. Over all the repair was easy, but pulling the agitator off was very difficult. I've got a strong grip and patience and after about 10 - 15 mintues of yanking on the agitator it came off. Don't try to use pliers as it will damage the plastic agitator. Replacing the hub drive and reassembly went very smoothly. The old hub drive wore out because it is plastic and connects to the metal drive shaft from the transmission. After years of torque, the hub will eventually strip out. Sooner depending on your usage and heavy duty cycles. In case you don't know, your machine might have the service manual in it on the inside of the body taped to the side. Mine helped me run through some troubleshooting steps and component tests to pinpoint to problem. Thanks Parts Select!

I did the repair just as the video showed, and had no problems at all.
the hardest thing I had to do was to move the washer out to where I could get to the back of the machine.
Due to the help of the sales rep and the video the repair was very easy

Thanks
Louis

I watched the video and did exactly what they said to do. It was really easy. The key to the success was in the parts that were mailed to me it had a separate piece of paper telling you to "reset" the washer after doing the repair. I missed this when I watched the video. That was a critical part of the repair which required no tools to accomplish.
I have done 6 loads of wash and the washer has not made any crazy noises and hasn't moved!

*be sure to turn water off, unplug machine, and unscrew the water hoses from the rear of the washer.
1. Removed screws from the back of the washer, just the top part where the controls are.
2. Removed the panel.
3. Use a putty knife or screw driver to pop off the top panel.
4. Remove the screws from the inlet valve.
5. Unplug the wires connecting the inlet valve to the washer.
6. Lift out the old inlet valve.
7. Replace with the new inlet valve.
8. Plug the new wires into the washer.
9. Replace the screws in the inlet valve.
10. Replace the top.
11. Replace the rear panel and screws.
12. Reconnect the water hoses, careful not to mix the hot and cold.
13. Plug the machine back in and you're finished!

Replaced the mixer valve . It was a few screws, and an instruction video from YouTube.

Tipped washer on its back & tookold Washer pulley assembly off & put new one on.

I unscrewed the top panel of the washer. I lifted up the top and used the pint scrapper to loosen up the lid switch and slid it out. I pulled the switch wiring harness out of the rear top of the washer. I slid the new lid switch and wiring harness back through the opening and secured the switch in place. Screwed it back in place. Took less than 15 minutes. I followed the instructions on the video, easy peasy lemon squeezy.

Following what the video shows how that they send with your part email, confirmation or receipt!! Easy Peasy!!

easy install 30-45min and a reset and it was done.

Actually, I "Youtubed" it. I entered the info from the washer and found what was similar. What would help is when you tilt the washer (on back or front) so you can look at what you're going to work on to match (or closely match) what is on Youtube. It is SO easy, it's unbelievable.

I put the dial to drain and and pressed the pause button for 3 seconds and it drained.
Unplugged the washer from the electrical outlet .
Shut the hot and cold water off. Disconnected and drained them.
Placed the washer on a soft mat on front side exposing the back and bottom of the machine.
Unscrew the metal cover with Philips head screw driver.
Disconnect the drain hose to a bucket or small dish tub .
Remove the belt cover with 5/8 ratchet or wrench.
Using a ratchet or wrench remove the one bolt holding the clutch in place .
Remove the two Philips head screws from the shift mechanism ( looks like clock timer,my memory is failing me right now sorry! ) .
Pull down on bottom gear after removing nut.
Push in and pull down with a flat head screwdriver on the tabs holding the collar in place above the top gear .The collar and gear and spring should come apart.
Install new parts in the same order . Reassemble make sure to use Locktite 242 on the bottom nut holding the gear.
Install belt , belt guard , cover drain hose . Stand machine back up , reconnect all hoses tightly plug machine into electrical outlet and start. Put a smile on your face because you did a great job and saved yourself some money!