7MWFW560CHW0 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michelle from Richardson, TX
- Parts Used:
- 72017
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from JUPITER, FL
- Parts Used:
- W11266654
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
It took two of us to hold the ring and slide it on around the opening with the assistance of screwdrivers the spring was very tight
Two people to screwdrivers, stretching the spring out and around and that’s the last part to go on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from SHERIDAN, WY
- Parts Used:
- W11316250
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Displayed “Door Loc” which was not correct error message
Replaced door latch after removing rubber seal from tub to access door latch. Simple replacement but did not correct issue. Notified service technician to determine error codes and had to replaced display panel and control module.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from ROUND LAKE PK, IL
- Parts Used:
- W11316246
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
PARTSSELECT IS THE PROBLEM
I asked PS if I purchase from them, will I get the new version level sensor or the old version in a sealed bag that has the new number on the bag.
They guaranteed I would get the newest version level sensor inside of the bag. I had this problem with the past 3 vendors) So i spent double the $ to purchase from them. it arrived, bag had new part # inside was the OLD PART numbered item! The would not respond! The link for the install wont work! I just need the newer part and the calibration procedure t make this right or a refund!
NO SUPPORT for PARTSSELECT!
They guaranteed I would get the newest version level sensor inside of the bag. I had this problem with the past 3 vendors) So i spent double the $ to purchase from them. it arrived, bag had new part # inside was the OLD PART numbered item! The would not respond! The link for the install wont work! I just need the newer part and the calibration procedure t make this right or a refund!
NO SUPPORT for PARTSSELECT!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nelson from Middletown, NY
- Parts Used:
- W10869845
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Washer Would Drain But Not Spin
Removed rear cover (6 screws) unpluged harness from motor control and removed same. Replaced motor control reinstalled harness. Replaced rear cover. Parts used motor control board.
Was this instruction helpful to you?
Thank you for voting!