WTW6120HC0 Whirlpool Washer - Instructions

The door strike part was very simple to remove. 15 seconds at most...Part ordered and delivered a day early. Install of new part was again about 15 seconds and Wala....job completed. Thanks for the great service....will call again when needed....

Removed two screws that held the control panel from the back with a power drill. Pop the control panel loose with a screwdriver from the top of the machine with the quick disconnects. After turning both the hot and cold water off I remove the hoses with pliers removed two screws with the power drill that hold the water inlet valve in place disconnected the wire harness plug And removed water inlet valve swap, the original harness to the new water inlet valve and follow the steps backwards to finish

Siphon break kit keeps washing machine from continuing to siphon after rinse/cycle -- like emptying a pool with a hose. Fixed the problem of the tub never filling due to siphon draining out water as it's being put in.

Watch video on the site and the insulation will be easy and take about 30 min.

DIY'er working on a Maytag Centennial type washing machine should be aware that replacing a a transmission or agitator due to worn out splines is only half a job done well. I originally replaced my transmission due to worn splines, only to discover later that the worn agitator splines caused the new transmission splines to wear out at an accelerated rate. Transmission and Agitator should be replaced together, along with a new Agitator mounting bolt. There are plenty of video's online of how to do this repair so I won't get into that here. Just wanted to drop the above sage advice. Transmissions for these washers aren't cheap.

The belt in this model is underneath the washing machine. Disconnect water lines and power cords, set up the drain hose in a bucket to avoid water spilling on the floor, tip the washing machine on its back, remove two bolt screws holding the plastic covering the belt, remove the old belt, and install the new one.

W10721967 Splutch Cam Kit

Assuming the pulley nut was properly tightened at the factory. I think this problem occurs because of ever-so-slight rounding of the splutch cam teeth from the actuator engaging and disengaging over whatever time frame there is before a clattering noise develops.

When I took off the 13mm nut using the adjustable strap tool, it felt tight to me...Was it put on as tight as it should have been at the factory? Who knows. I don't have the torque specification of this nut on that plastic pulley.

Watch the videos to remove and replace the belt cover and belt, actuator and splutch cam kit.

Pay particular attention to tightening up the nut. I put the pulley on and hand-tightened the nut. I used the adjustable strap tool and before I tightened everything, I pushed up on the pulley to press against the spring pressure in order to mesh the teeth together. After the nut was tight, I repositioned the strap tool and gave it another go, further tightening it. You see earlier that day, I only tightened it up once because I thought it was good and tight. I put everything back and within a half-hour it was clattering again and I could loosen the nut I thought was tight by hand! I fooled myself. That's why I did it twice, and don't be afraid to give it a good second tightening effort. Two weeks now and the wife is currently very happy.

Turned off power and water. Removed hoses/Unplugged power. Removed screws to open and access control panel. Removed existing valve first by pinching off 6 wire connectors then screws securing valve to washer base. At this point, I replaced with new valve and reattached everything. I also added screen washers to both hoses as I suspect it was built up debris in original valve impeding water flow through valve that led to problem…

a couple of issues to get valve out and off , 15 min. install and top back on!!!

I put the dial to drain and and pressed the pause button for 3 seconds and it drained.
Unplugged the washer from the electrical outlet .
Shut the hot and cold water off. Disconnected and drained them.
Placed the washer on a soft mat on front side exposing the back and bottom of the machine.
Unscrew the metal cover with Philips head screw driver.
Disconnect the drain hose to a bucket or small dish tub .
Remove the belt cover with 5/8 ratchet or wrench.
Using a ratchet or wrench remove the one bolt holding the clutch in place .
Remove the two Philips head screws from the shift mechanism ( looks like clock timer,my memory is failing me right now sorry! ) .
Pull down on bottom gear after removing nut.
Push in and pull down with a flat head screwdriver on the tabs holding the collar in place above the top gear .The collar and gear and spring should come apart.
Install new parts in the same order . Reassemble make sure to use Locktite 242 on the bottom nut holding the gear.
Install belt , belt guard , cover drain hose . Stand machine back up , reconnect all hoses tightly plug machine into electrical outlet and start. Put a smile on your face because you did a great job and saved yourself some money!

Unplugged the microvave, removed the phillips screw holding the right hand section of the microwave in place (Note: This screw is found by looking through a vent opening in the TOP of the microwave body.). Lifted up and out on the right hand section of the microwave. At this point the right hand section is completely unattached to the microwave body. Unplugged all of the polarized wiring harnesses and removed the screw holding the green wire to the board holder. Removed the screws holding the board to the right hand section and installed the new board. Reversed the procedure to put the microwave back together. Note: Look at and manipulate the keypad ribbon recepticle on the new board to see how to remove and reattach the ribbon, if needed.

Followed detailed instructions which were supplied with the parts. It was easy and my machine is working great with no issues. Also I just didn’t get the main drive pulley, all new parts came for the bottom end, great service and excellent parts.

Removed the top screw holding the control face. Lift up on control face and tilt outward to unplug wires and remove green ground wire screw. Place unit on a flat surface and remove flat wire plug by squeezing tabs and lift up slightly then remove flat wire. Unscrew screws holding PC board. Then reverse order the install of the new PC board and install unit on to microwave.

Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.

Ordered drain hose extender. It uses a rubber flange with hose clip to attach to washer's plastic hose. When tightened, the hose clip crushes the plastic hose and crimps it, causing a leak. My solution was to find a copper pipe flange that was the same diameter as the interior of the plastic hose to act as a bushing for the plastic hose. The hose clip could then be tightened without deforming the hose. Worked great with no leaks.