WTW7120HC0 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Emmett from WEATHERFORD, TX
- Parts Used:
- 40922
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Socket set
Needed to extend drain hose to reach drain
Ordered drain hose extender. It uses a rubber flange with hose clip to attach to washer's plastic hose. When tightened, the hose clip crushes the plastic hose and crimps it, causing a leak. My solution was to find a copper pipe flange that was the same diameter as the interior of the plastic hose to act as a bushing for the plastic hose. The hose clip could then be tightened without deforming the hose. Worked great with no leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from PINE MOUNTAIN, GA
- Parts Used:
- 8212641RP
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Washer hoses due for replacement
Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from LINN CREEK, MO
- Parts Used:
- W11220230
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Socket set
no water to washer
a couple of issues to get valve out and off , 15 min. install and top back on!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from CANADIAN, TX
- Parts Used:
- W11220230
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Washer won't fill with water, Error Code LF showing on display panel.
Watched and followed You Tube Video . "Solved: The Fix for a Whirlpool Washing Machine that won't fill with water." The video is a little over 8 minutes long. At that start of the video he encourages you to watch all of the video for special instructions near the end of the video. You need to do that! I put 30-60 minutes, but actual time was 4 days as I had to order parts and wait for the parts to arrive.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from BELLEVIEW, FL
- Parts Used:
- W11552018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
control board
took the front right side of the microwave off took the oldcontrol board out and install the new one apiece of cake
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jerry from BRYAN, TX
- Parts Used:
- W11552018
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The microwave magnet would start when the door closed w/o a keypad signal.
Unplugged the microvave, removed the phillips screw holding the right hand section of the microwave in place (Note: This screw is found by looking through a vent opening in the TOP of the microwave body.). Lifted up and out on the right hand section of the microwave. At this point the right hand section is completely unattached to the microwave body. Unplugged all of the polarized wiring harnesses and removed the screw holding the green wire to the board holder. Removed the screws holding the board to the right hand section and installed the new board. Reversed the procedure to put the microwave back together. Note: Look at and manipulate the keypad ribbon recepticle on the new board to see how to remove and reattach the ribbon, if needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Jupiter, FL
- Parts Used:
- W11220230
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set, Wrench (Adjustable)
Cold water stopped working
Pried open the top of the machine. Used a putty knife. This was the hardest part of the job. Take your time. Took off upper plate of the back of machine, to free the value. Unplugged the power wires from the old valve and unscrewed it. Put in the new one and reversed processes. Easy peezy. Great deal on part. Saved hundreds of dollars doing it myself
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from INMAN, SC
- Parts Used:
- WPW10238319
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Door alignment
I was sent the wrong part , when I questioned them said they did not have it so was directed to Whirlpool and they are making it and I might get it in May
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Morgan from ASHLAND, KY
- Parts Used:
- W11552018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light under Microwave stopped working. No power from PC Board.
Removed the top screw holding the control face. Lift up on control face and tilt outward to unplug wires and remove green ground wire screw. Place unit on a flat surface and remove flat wire plug by squeezing tabs and lift up slightly then remove flat wire. Unscrew screws holding PC board. Then reverse order the install of the new PC board and install unit on to microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!