WTW7120HW0 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Thomas from MILLBURY, OH
- Parts Used:
- W10752187
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Worn out splines connecting transmission driveshaft to agitator.
DIY'er working on a Maytag Centennial type washing machine should be aware that replacing a a transmission or agitator due to worn out splines is only half a job done well. I originally replaced my transmission due to worn splines, only to discover later that the worn agitator splines caused the new transmission splines to wear out at an accelerated rate. Transmission and Agitator should be replaced together, along with a new Agitator mounting bolt. There are plenty of video's online of how to do this repair so I won't get into that here. Just wanted to drop the above sage advice. Transmissions for these washers aren't cheap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from LINN CREEK, MO
- Parts Used:
- W11220230
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Socket set
no water to washer
a couple of issues to get valve out and off , 15 min. install and top back on!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jerry from BRYAN, TX
- Parts Used:
- W11552018
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The microwave magnet would start when the door closed w/o a keypad signal.
Unplugged the microvave, removed the phillips screw holding the right hand section of the microwave in place (Note: This screw is found by looking through a vent opening in the TOP of the microwave body.). Lifted up and out on the right hand section of the microwave. At this point the right hand section is completely unattached to the microwave body. Unplugged all of the polarized wiring harnesses and removed the screw holding the green wire to the board holder. Removed the screws holding the board to the right hand section and installed the new board. Reversed the procedure to put the microwave back together. Note: Look at and manipulate the keypad ribbon recepticle on the new board to see how to remove and reattach the ribbon, if needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emmett from WEATHERFORD, TX
- Parts Used:
- 40922
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Socket set
Needed to extend drain hose to reach drain
Ordered drain hose extender. It uses a rubber flange with hose clip to attach to washer's plastic hose. When tightened, the hose clip crushes the plastic hose and crimps it, causing a leak. My solution was to find a copper pipe flange that was the same diameter as the interior of the plastic hose to act as a bushing for the plastic hose. The hose clip could then be tightened without deforming the hose. Worked great with no leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from INDEPENDENCE, KY
- Parts Used:
- W10752187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
the impellar mechanism wore out so stopped aggitating
Popped the cap , used a socket to unscrew the bolt (it was stripped so ended up having to cut off bolt) Took off old impellar and replaced, installed a new bolt, replaced Cap and it was fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Morgan from ASHLAND, KY
- Parts Used:
- W11552018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light under Microwave stopped working. No power from PC Board.
Removed the top screw holding the control face. Lift up on control face and tilt outward to unplug wires and remove green ground wire screw. Place unit on a flat surface and remove flat wire plug by squeezing tabs and lift up slightly then remove flat wire. Unscrew screws holding PC board. Then reverse order the install of the new PC board and install unit on to microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from PINE MOUNTAIN, GA
- Parts Used:
- 8212641RP
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Washer hoses due for replacement
Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from DREXEL HILL, PA
- Parts Used:
- W11244231
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Replace drain hose
At first I had to position the washer so I could get access.. after having it positioned, I figured it out. Getting the clamp fastened, I was done.
Was this instruction helpful to you?
Thank you for voting!