GHW9460PL0 Whirlpool Washer - Instructions

Just removed two screws with a phillips screwdriver and screwed the new handle on. Super simple

Easily. 4 Screws. 2 Clamps.

Lined the new one up with one hand;(cold beer in the other), snapped it to place, finished.

Inserted new baffle in washer and slide in place.

Followed directions as shown in your repair video, having done this for the first time it took a bit longer than a repairman would have but was able to git-r-done. The most difficult part was fitting the adjustable wire back around the front of the washer, in the video it is made to look really easy however in real life it is a little more difficult and could not be attached so easily and took quite a bit of time to make sure it was attached correctly. thank you for your help.

1. Remove bottom panel (3 screws below). 2. Remove top panel (3 screws back). 3. Remove detergent dispenser (remove T screw in front.) 4. Carefully remove control panel is plastic so be careful not to break it. 5. Pull broken bellow from front and spring loaded clamp will come lose. 6. Push away bellow. 7. Remove cables from door lock. 8. Remove front panel screws (4 - 2 on top and 2 in bottom). 9. Unscrew bellow's clamp with flat screw driver or not driver. 10. Remove worn bellow. 11. Bellow has notch on top (Use as reference to replace. 11. Clean all surfaces. 12. Install new bellow to drum. 13. Screw clamp over of bellow not too tight. Don't want to break the seat. 14. Replace all in the reverse order and for the front of the bellow refer to my previous article (story) on front latch replacement.

This was truely easy. All I needed was a flat head screw driver and it was done within five minutes.

Removed the outer spring with pliers. Pushed the bellow into the drum. Loosened the clamp on the bellow with a stub nose screwdriver. Removed the bellow. lined bellow up with soap fiting. Reversed procedure to reinstall.

Had the old pump out - 1 screw and two hose clamp to unhook and an electrical wire to pull out - couldnt been any easier - when new one came took 5 mins to install - did a load to make sure pump worked before put it all back together

First I removed the two screws that held the old handle and then replaced the new handle with the same screws.

First, I unscrewed the two screws on the broken handle, using an allen wrench. Then, I screwed on the new handle in it's place. The new grey handle is much lighter in color than the original charcoal grey of the washer, but it blends well and works perfectly.

I purchased a new bellows from this site I followed their instructions. Just tricky getting the inner clamp on aligned and tightened.

I had units stacked so I had to take the dryer off, pull 3 screws from back, slide cover back and the water valve is right there, easy to change. I have not had the problem since then.

2 clamps and its off, problem is if you have average size hands you will struggle in getting the back clamp on and off.

Inputs on your web site of other people who had replaced this valve assembly helped.
Remove top cover from washer - three socket head screws on rear of machine, (need to move washer forward for access)
Turn off both hot and cold manual shutoff vales on wall. Run washer to take water pressure off from hoses (turn on for water to turn on , and then turn washer off).
Remove both hoses (mark/remember which side is hot/cold, as valve assembly has no markings), from valve assembly, had to use channel locks/adjustable wrench to remove nuts as they were really tight. Check to see if gaskets were OK, would have been nice, if these gaskets are supplied with new valve assembly. Remove screw which holds valve assembly to washer. Slide valve assembly slightly side ways to free it from bulkhead panel. Remove last hose assembly inside washer, attached to valve; remove four wires from solenoids. Keep track of wires (which solenoid).
Replace valve, reconnect internal hoses and wires; install valve assemble on bulkhead panel; attach screw; reconnect hoses; turn on manual valves; check for leaks; briefly turn on washer, check for internal leaks; install cover; push back washer in place.