6ALSQ8000MW3 Whirlpool Washer - Instructions

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

1. remove 2 hoses at pump using pliers to open hose clamps and sliding them out of the way.
2. remove 2 retainers holding pump with screwdriver.
3. remove old pump and install new pump
4. clamp pump using retaining clips
5. re-connect hoses

Although your website mentioned removing 2 screws to open the control panel, it took a while to realize there were 2 screws and 2 hex nut screws to open it followed by 15 minutes of efforts to release the control panel from the top of the washer by sliding it forward. After that it took 2 minutes to replace the switch; the web comment of keeping the lid open was helpful.
Unfortunately, the lid switch was not the problem; replacing the timer did the trick, was very easy with the control panel already opened and required the purchase of 1/4 and 3/16 hex nut drivers.
Parts, shipping and tools cost $110 but the success of the repair with your parts and advice was priceless.

Unbalanced load was creating a knocking sound (as if the clothes load was unbalanced). Dismantled the washer to find that one brackets had rusted out. [FYI: 3 bracket at 120 degree apart (for the 360 degree circle)]. I found that the hole (on the bracket) where the spring holds was gone. Purchased parts. Replaced them (spring, bracket, screw). Reassembled washer then ran wash for a cycle. Successful fix.

First I removed the two screws holding the main controller located on the back. I then slide forward the hole controller and I pulled out. Disconnected switch located on your left. (remember to place down washing machine lid before installing the new switch.)

Remove the main bolts that hold the gearbox in place, pull the gearbox and shaft out. You will see the brake shoes and drum--the large spring is a struggle to replace. Getting it out was not hard. The biggest struggle I had was replacing the brake shoe spring after replacing the shoes. I ultimately compressed the spring in a vise, then used safety wired it, then placed it between the shoes, then cut the wire to relaease the spring.

With the PartSelect website instructions, I was able to take the agitator apart easily, diagnose the problem and select the replacement parts to effect the repair. The only issue I faced was the shipment damage to the repair parts, but the service department with PartSelect responded quickly and fairly to correct the damage. I have never seen a website like PartSelect.com that trains you in making the repairs, provides you with the required parts and then stands by to resolve any issues you face; I was awed by how confident that it made me feel throughout the process.

1) Unplugged electrical cord
2) Removed hot/cold water hoses
3) Took drain hose from laundry room recepatcle
4) Moved washing machine to area where I could lay it down on its back (very important for easy fix)
5) Found (easy accessible in my case) water pump with an inlet and outlet water hose held on with spring clamps.
6) Removed each of the two clamps with pliers and each hose by twisting loose
7) Remove two metal clips holding pump to motor housing
8) Slide pump off shaft - removal is finished!
9) Reversed process for installation, making sure to gently align pump housing when the pump is aligned with the shaft
[probably took less than 15 minutes]

First, I'm so excited that this site exists because I knew that the problem was minor and I didn't want to pay the outrageous housecall price of a repairman. I read other customers' experiences on how they fixed the problem and that made it sooo easy! Basically unscrewed the screws on the far left and right on the top panel, folded it down toward front, unscrewed and unplugged the ground wire and replaced the part. Someone else had warned that the lid should be open to remove it and that was a huge time-saver. Thanks so much! The part was broken because of very poor design. The part actually worked fine, but the piece of thin plastic that held the part in place broke. Back to the drawing board Whirlpool.

I thought the click of the lid switch sounded different so I pulled the top console and tested it for continuity in both positions and found none. When I by-passed the switch the washer started up, so I knew what the problem was. There are four screws involved to remove the console which reveals the lid switch to the left side. There's a single screw for a ground wire but the switch itself is simply snapped in place after disconnecting the wire harness plug (must be done with the lid open btw).

I was lucky to diagnose the problem accurately so that the first thing I suspected turned out to be the problem!

I removed the screws holding the control board in place. Removed the knob on the front of the panel and then disconected the wires to the control. Then I took the old control off the board and inserted the new control. I attached the wire connectors to the new control and put the control panel back in place and fastened it with the screws. Last task was to replace the knob. The new control worked wonderfully with the first load of laundry. Piece of cake. Done in 5 minutes or less.

I just took the cap of the agitator off and the 3/8" nut was right there. I took it off with a socket, removed the top agitator, slid the assembled kit in , replaced the agitator and cap...that was it !!. These parts priced thrrough Sears were $77.00 plus S&H. Your price for the entire kit- less than $12.00 !! If you don't think that you can do this yourself, have your 7 year old child do it. Took me about 5 minutes. Great price and fast shipping. Thanks

Laid washer on front side and removed top spring, then lifted the tub assembly to replace the right side spring, the one behind the motor was the hardest, I lifted the tub then removed the spring bracket at the tub with pliers and a socket. The top seal all I had to do was take the 4 screws that hold the top on (it takes a long extension) then sit it bak up and I lifted the top up to give me enough room to unsnap the top piece of the tub, cleaned it up put seal in. The parts fit perfitlt and real fast shipping, I bookmarked the site and will buy from again. JIM

Removed top cap on agitator w/ flathead screwdriver. Removed protective cap over bolt and cog housing shaft. Used 7/16 deep socket w/ extension to remove bolt. Removed housing where stripped cogs were located. Cogs seated loosely in shaft housing no tools required to remove cogs. Replaced cogs in housing, made sure everything was lined correctly. re-inserted housing into shaft. ,screwed bolt, replaced caps and works like new.

turned the washer on it's back and shoved the tub to the side to release pressure on a spring ,pulled it loose and installed new one. this worked for the back two then turned washer on it;s face and repeted the process on the front spring.
Washer works great now.