WFW8410SW0 Whirlpool Washer - Instructions

Watched the videos which were key! Thanks Parts Select! Replaced Bellows and dispenser hose. Cleaned all areas really well where new hose and bellows attached. Ran the washer in "clean washer mode" twice. Not a drop leaking. Thank you!

First unplug the washer and turn water off..Next take off back of the washer ( I used a socket set). Then underneath the front load tub, take that panel off to get to the pump (there are 3 screws in the front panel). Then get a towel put it underneath the water pump. Next take your pliers and squeeze the tab holding the end of the drain hose where it connects to the pump, Slide the clip up on the pump connection, pull off hose ,make sure your towel is underneath the end of the hose.Next reach your hand through the back of the washer and squeeze the plastic holder w[th your hand to release the hose. Then pull old hose out and replace it the the new hose. Just reverse the steps to put it in..

Much easier than I thought. Watched the video a few times.The front control panel gave me a little fight which the video edited that part out And the spring clamp reinstall took the most time.There must be a tool for that??

Followed the video except to use clamps to hold the Bellow To Front Panel Clamp in place while I worked the clamp around the from of the Bellow. I used a plastic pry tool in place of the suggested screw driver to pry the control panel off.

I followed the video that accompanied the parts order confirmation. The replacement of the two parts, bellows and hose, were pretty straightforward. The job took a little less than an hour with little aggregation.

Used suggestions on list - water to lubricate bellows and an extra hand to secure the bellows. Biggest challenge was seating the bellow that attaches to the rim of the outer tub. After getting the bellow lip seated the rest was fairly easy including the bellow seat that secures to the outer door assembly. Unfortunately, it doesn't appear that the bellow was the problem even though the symptoms - leaking under the door - was the same as noted on the list of problems. Had to order the dispenser-to-tub hose as that looks to be the problem (had to contort to follow the leak all the way up to the hose).

Replace front legs. Very easy fix.

raised front of machine about 6 inchs bigest pain is getting water out after that its easy.open drain just a bit other wise it will pour out all over about 4 pots worth if its full

Replaced drain hose

Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.

The repair was simple as you can imagine. Thought I could buy these legs at any big box store or at least at the local hardware store. No such luck. Partselect had the right product---easy to order and easy to install. Things around here are great.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

This was an easy fix . PartSelect was quick and had all the info I needed to repair my washer. Plus shipping was super fast. Thanks

Followed the most helpful video.with some system differences. Had quite a bit of fitment challenge with the inner bellow sealing process...finally used dish soap to help 'stretch' the thing on.Works fine now thanks.

The removal of the bellows was easy and quick. The instructional video was really good. Only one problem with video. The step of removing the console from washer leaves out that there is a center screw in the center of console. I almost broke the console. It took took a long time in getting bellows on interior area due to tight finger space. Wire gasket fairly easy. The outer gasket after getting door and latch on. Whew! That was a bear. Video looked easy. I finally had to get help to get it on. The reason was that every time I thought I had it, the bellows would roll off will the wire gasket. A screw type as the inner area would make it so much easier. Shipping. Kudos to your company. I was expecting that I would be without washer for a week. I ordered on a Friday and it was here early Monday morning. That was amazing. By the way I did this except the outer wire gasket by myself. I finally had to get "husband" to help with that. Thanks Parts Select! If the need arises that I need another part. You will be my go to company.