GHW9250MW0 Whirlpool Washer - Instructions

I had units stacked so I had to take the dryer off, pull 3 screws from back, slide cover back and the water valve is right there, easy to change. I have not had the problem since then.

Inputs on your web site of other people who had replaced this valve assembly helped.
Remove top cover from washer - three socket head screws on rear of machine, (need to move washer forward for access)
Turn off both hot and cold manual shutoff vales on wall. Run washer to take water pressure off from hoses (turn on for water to turn on , and then turn washer off).
Remove both hoses (mark/remember which side is hot/cold, as valve assembly has no markings), from valve assembly, had to use channel locks/adjustable wrench to remove nuts as they were really tight. Check to see if gaskets were OK, would have been nice, if these gaskets are supplied with new valve assembly. Remove screw which holds valve assembly to washer. Slide valve assembly slightly side ways to free it from bulkhead panel. Remove last hose assembly inside washer, attached to valve; remove four wires from solenoids. Keep track of wires (which solenoid).
Replace valve, reconnect internal hoses and wires; install valve assemble on bulkhead panel; attach screw; reconnect hoses; turn on manual valves; check for leaks; briefly turn on washer, check for internal leaks; install cover; push back washer in place.

Remive 3 screws along bottom front panel and remove that by pulling down and off. Remove 4 screws from the back of washer along the top to remove top cover. Pull out dispenser tray. Remove 2 screws from along dispenser, then carefully remove the control panel by inserting a screwdriver to release internal clips along the top. Put the control panel on top of the washer. This gives you access to 2 more screws at the top, and also 2 screws on the bottom, that will release the door panel. You'll have to disconnect 3 wire connections to get access to the wide rubber gasket (bellow). There is an inner ring and an outer ring holding it in place. The outer ring is a spring. Pull that off. Then remove the inner by loosening the screw holding the clamp. Pull the bellow off and replace with the new one. Make sure the gasket goes completely over the large water spout and the smaller button sprayer at the top taking caution to have the gasket sit between the two plastic washers attached to it. Make sure the belllow is firmly seated inside and out before attaching the bellow. Reattach everything in reverse order. Problems you'll run into: getting the spring on the outer gasket as it is tight to get on and the rubber will keep slipping off the edge where it is seated. Also, you may need an extra pair of hands to hold the door up while you attach those wire connections as there is no play in the wires.

As easy as 123 two torx screws removed old pieces and install the new one and like that ready for another 15 years.

The baffle just slipped on with no tools required. The best thing was that we received our parts the next day after ordering them, and we just paid for regular shipping!

the old handle was held in place with two screws.
the screws were removed, handle came off right away and then the new handle was place on the door and the screws were replaced.

First, I unscrewed the two screws on the broken handle, using an allen wrench. Then, I screwed on the new handle in it's place. The new grey handle is much lighter in color than the original charcoal grey of the washer, but it blends well and works perfectly.

Simple. Found my torx bits, removed the screws, removed the old handle, placed the new handle in position, replaced screws.

This happened because I failed to wait for the click on the machine before I opened the door. It's a front loader and it needs time to drain the water before you open the door.

Remove top 3 screws.
Remove 1 screw that holds inlet valve.
slide valve to the right.
Mark and remove 4 connector wires.

Reverse order to install.

First I waited 6 days after i was E-mailed the part was shipped until it was shipped, then waited two more days to get the part!
Then i removed two TORX screws removed old handle then installed the new one in reverse order.

I unscrewed thebolts from the old handle using a small flat screwdriver and removed the cracked handle. I then tossed away all the old duct tape holding the old handle together. Replaced new handle using same old bolts.Strongly cautioned children and husband to not wrench the washer handle open and closed. Tah Dah! Done.

Took two screws out, removed broken handle, replaced with new handle and put two screws back in. Ridiculously easy. :)

Unscrew old one,screw on new one

Removed 2 torx head screws and replaced handle

I removed two screws and removed broken piece and replaced the handle with the same two screws. The color and match of the handle was perfect.