SWS833HS1 Westinghouse Washer - Instructions

Two small clamps holding the top onto the body were removed with two screws. I lifted the top and held it up with a small piece of board. Two screws were removed on the back top left that hold the water inlet valve in place. Once those were removed I reached inside and removed the two plugged in wires and and lifted the part out. At this point I used pliers to unclamp the hose that fed into the washer. I then reversed the process and put in the new part. Works great. Thanks a lot for making the part I needed easy to find. I am now a true fans of your website.

Removed screws at back securing top panel (4).

Removed screws holding water inlet valve to back of machine (2)

Removed water hoses to bucket

Removed squeeze clamp securing water distribution hose from inlet valve

Reversed method with new valve.

Very fast...~25 min
Works fine so far!

Unplug washer. Remove supply lines. Remove two screws in back and remove clips holding top of washer. Front of washer top is held by two clips. Release top from clips and slide top towards the front. Remove two screws holding the water inlet valve to the back of the washer. Lift unit out and remove clamp and hose. Install new unit in reverse of removal.

The repair would have gone much easier if I did not have a stack dryer on top of the washer. Had to roll out the total unit and work with the dryer partly on top. Only needed minimal work and tools after that.

Shut off water to washer....unplug power cord...pulled washer from wall out into room....removed 2 water supply hoses....removed 2 top retaining clip screws on rear top of cabinet.....lifted rear end of top panel up approx 5 inches......propped up with small pieces of cut up 2X4 lumber.....did not disconnect any wiring related to the control panel...remove 2 screws holding valve to cabinet back panel......lift valve up and out of cabinet by the tub fiil hose.....disconnect 2 wire plugs, mark these upper, lower or hot /cold......disconnect the tub fill hose....remove the back panel-to-valve bracket off the old valve and install on the new valve and reverse this procedure!!! The new valve flows water better and faster, the wash is done quicker!!

It is so great to be able to turn my dryer on now without using my bare hand to turn the shaft that the knob was to go on. Nothing needed other than pushing knob in place. I so wish I had thought of looking online for a replacement part 4 years ago. Thanks!

Extremely easy. From finding the part on the website to installing on the machine.

I ordered replacement knob for washing machine. It arrived by fedex in 3 days. Ordering was easy and transaction went as smooth as it could. I will order again if needed.

Just put the new one on! Absolutely great service!!!!
A+++++++++++++++++++++++++++++++++++++

watched the video, all instructions were perfect!

Pushed on new knob.

It took longer to remove and then replace the back of the washer than to replace the water inlet valve. The video made it look easy and it was!. For the next perso: remember that if the water valve springs a leak and the washer has water in it, turn the dial to spin and the water will leave the drum. No need to siphon out the water.

removed and replaced pump

lifted up top panel unscrewed two phillips screws at bottom of front panel, lifted up and out and removed the panel exposing motor and belt .pushed in belt tensioner and removed belt.Then I slid the new belt under the tub pulley and rotated it until belt was on both the tub pulley and motor pulley,released belt tensioner and the job was over,

Used a metal cooking spoon to pry open the lid, held it in place with a chain (mentioned in the tools required) and used needlenose pliers to remove the clamp on the old hose assmbly. Transferd that clamp to the new hose assembly and replace the (1) screw holding it in place. Closed the lid of the washer, and now it is like the problm had never existed. (Very easy fix, 1 of 10 on difficulty scale).