SWX703HS1 Westinghouse Washer - Instructions

It turned out that the pump was fine. There is a filter within the rubber bellows between the washer drum and the motor. You need to remove the entire bellows to get to it. Just remove the motor and you can un-clip the hose tensioners. They are exactly like the ones you would fine on most foreign cars - just compress with pliers and move back on the hose. Clean out the plastic filter. A small nail had worked its way through the plastic filter and lodged in the motor impeller. Removing this nail and reassembling, it all worked as new! I kept the pump and motor as a future spare rather than return it.

i took out the two back screws lift the top.
took the two bottom front screws , lifted andtook off the front panel.took off the old belt an intall the new one in a circular motion put the panel and top back on and done.

Once I figured out that it would not spin because it did not drain. Unplug machine and remove the back pannel. Locate the drain pump on the bottom of machine. Remove the power wires and the screws holding it to the bottom. Then use a pliers to remove the hose clamps ( was easer for me to tip the machine forward ). Be prepaired to catch or soak up extra water from lines. The hardest part to the install is the limited room you have to work with. Install screws to hold the pump in place then install water lines, power wires and back pannel. Only thing left is to plug it in and watch for leaks.

First I removed the front panel,then set the timer to run. It began the drain,spin cycle, pump ran, but no water went out. Shop-vac the water out,removed hoses from pump,took out mounting screws from base, unplug pump plug. check hoses for debris since they're open, the impeller was broken. ordered the part . Mount the pump to the base, put the hoses on, plug in motor and replace front panel. plug into wall

Removed 2 screws at bottom of the front panel - removed front panel by sliding the panel down about 1/2 inch and then away from the appliance- v belt is removed by pushing the tensioner pulley to remove tension from the belt and turning the pulley untill the belt is removed instalation is a simple reverse of the process. I did't have a repair manual so every step was trial and error untill I was able to complete the repair.

First I took sides off the washer. I then took screws out of the Drain pump holder. Unclamped the two pipes from it. Undid the wires to then drain pump. Screw in the new pump hardware. Plugged in the wires on side of the pump. Reclamped the pipes. Put sides back on washer and it worked. That easy and took less then 30 minutes. I am no handy man so thats how easty it was.

I got online and figured out exactly how to take off the front of the washer and then how to replace the belt. It was so easy. The part itself arrived much sooner than predicted. It fit perfectly and my washing machine is now running smoothly and quietly.

My washing machine stopped agitating and spinning and I couldn't afford a repair man...plus I wanted to exhaust any obvious problems first. One of the leveler feet had broken years ago. Since I luckily had determined via reading other posts that the agitator won't work if the cycle safety switch is not functioning right, I thought the safety switch might need to be changed but after careful thought, I decided to order a new levelling leg first because maybe the broken levelling leg was shaking the safety switch so it wasn't connecting right. Once I received the leg overnight, I flipped the washer on its side and had to drill out the old leg. It was a little tricky because of how it broke, but the drill worked. I flipped the washer back up, leveled it with the new foot, and the agitator was miraculously working again...just like new. I didn't need the safety switch. Thanks to partselect.com for having the details of my washer parts to study up on and get me the right part so quickly. I saved myself alot of money.

After moving machine to an area that allowed easy access to the unit, disconnected the water supply hoses from the inlet valve.
Removed the two screws that keep the back in place, removed the clips that keep the top in place, moved the top over far enough to get the valve out. Removed the screw that keeps the inlet valve in place, disconnected the power supply to the valve, Pulled valve out in order to remove the water outlet hose. Repalced with new vale, and reversed order to install. Works just fine now.

Checked problem on-line and discovered it was the water inlet valve. Matched the part on part select. Com. Finding the part was very easy. Part select had a grid behind the picture to help determine the size and pictures from all sides. Removing the old part, matching it, and replacement took a total of 30 minutes. I now have clean clothes.

First I removed the two screws that hold the pump in place. I then pulled the pump out and replaced it with the new pump.

i removed the front panel, then removed the old pump by taking off the clamps and disconnected the wiring. The new pump had to be reversed before connecting, but it was so easy.

followed the instructions on a blog

Lifted top
removed adgetator
removed tub top
removed inside tub
removed inside tub holder bracket
repaced seal
replaced,replaced.....

S/O Water , Removed front panel, removed screws from side panel water valve accessible. Removed screws that hold water valve, installed new valve reassembled washing machine.