WWS833ES0 Westinghouse Washer - Instructions

carefully pry up on front washer top to release plastic keeper pins,remove 2 phillips screws from beneath lower front washer panel,slightly lift upward on panel to release.remove old broken belt,push new belt beneath large tub pulley,put belt on small motor pulley,push back belt tension /idler arm,start belt on large tub pulley,turn tub pulley by hand to run belt on,release tension on idler arm.replace front panel and lower top.WALAAH!!!! you are done.

uplugged washer took front off washer 2 screws pryed up top pump was mounted with 2 screws and 2 wires took off found change in pump and the fins to pump worn off ordered part off line the wait for part was longer than the amount of time to fix problem and cost of part saved me about $25-35 if I was to buy local worth wait save money and fix problem washes like new spins and drains all water from tub.

After reading the possiblilities of problem, I determined that the drain pump was not working; therefore I ordered a new one. When I opened the washer to replace the part, I found out that the pump was working but the filter was stuffed with pieces of rubber that came out from a rug I washed. Once all the stuff was removed, the washer worked just fine. PartSelect was very gracious to accept the returned with not questions asked!! Thanks partSelect.

The Lid Lock Assembly came super fast! The install would have been flawless, but the "pre-drilled" holes on the new Lid Lock Assembly were way to small. We found that out after we had reconnected the wires and gotten it into place. Aside from that small set back, the install went great! This repair is definitey not one that you would need to pay a repair person to do!

Removed two screws at bottom of front panel, removed front panel. Used pliers to remove hose clamp on drain hose. Fished hose out of chassis and installed new hose. Tested for leaks.

Disconnect water and electricity.
Shop-vac out the water in the internal drain hose.
Remove back cover, tip washer on side to gain access.
Un-clamp rubber drain hose,unscrew pump and remove.
Cleanout filter cup (yuk!) find coins and hairpins.
Attach drain hose to new pump and re-install with hose clamps from hardware store because spring clamps were impossible (arthritis in fingers).
Reconnect water and electricity.
Test for leaks and tighten clamps if necessary.

The problem with my very old washer was that the tension spring had broken long ago and I had jerry-rigged it in place with a cable tie. It would work, but you had to give the drum a spin by hand when it hit the spin the cycle. This probelm further caused the premature wearing of the drive belt, due to slippage. I ordered both a new spring and a new belt. Upon their arrival, I removed the two screws holding the front panel and lowered it off and out of the way. The old, worn belt was very easy to remove, as there was very little tension on it. Next I attempted to remove the washer that holds the idle arm on. It is in a very awkward spot, and it appears the the washing machine is sort of built around it. I bent it gradually with locking pliers until I could force it off with the blade of a flat screwdriver. Then the idler arm was easy to lower of its axle by twisting the drum a bit and pulling it to one side. I put the new spring into the idler arm, making sure the plastic bushing was in place and replaced the arm. I then repositioned to belt and replaced the front panel. It works great now.

Removed fastening screw and Agitator. Removed and replaced Agitator Drive Block. Replaced and fastened Agitator. Done in 5 min.

Ordered part around noon. Shipping was 3-5 days. Part arrived in LESS than 24 hours.

Very happy camper here!

I removed front and top of washer to get acess to the tub. removed cap to tub along with inner tub and agitator. the hardest part is removing the springs on the bottom and tilt it forward to get tub out. removed belt, pulley and bolts holding transmission in place. reassemble using silicone grease on seals and washers. works great now

pulled old knob off. pushed new knob on.

Unplugged machine.
Turned off water supply.

Removed front panel.
Pushed in on belt tensioner, removed old belt, replaced with new belt.

Used pry bar to lift the base assembly high enough off the snubber to remove it. Partially propped it with 2x4 wood scraps.

Used bent clothes hangar to remove old snubber ring, to protect my hands.

Replaced snubber, arrow pointing up.
Carefully lowered base assembly.

Replaced front panel.
Turned water back on, plugged back in, washing machine no longer 'walks'.

Remember to check the washer against a level if you moved the machine.

removed upper cover, removed front cover, tested switch with digital VOM, removed and replaced!
2 screws, 4 wires! saved over $100 when compared to a bill from a repair service!

fast shipping too! will recommend others!

unscrew the top from the back. lift it up. Support the top and then unplugged the old valve, unscrewed it took the drain hose off it and presto the old came right out. align the new one was a little tricky and attached the drain hose and tightened the screw hook up the wires reattach the top and I was done. 30/45 minutes. I was really surprized that the part I ordered was the same one I took out. Thanks for being there.

My first step was to download and print out the parts diagrams from the manufacturer's website. With a basic idea of what I needed to get to I first removed the agitator cap and the agitator and right off I found a broken bolt on plate lock bracket that holds trunnion which supports and connects the tub to the transmission drive shaft. I replaced the bolt and put it back together and gave it a test run. Spun very nicely now but water was going everywhere. Unfortunately I found that when the bolt broke the tub had slipped down and ripped the rubber "tub seal assembly". To get to the seal I ended up tearing the machine completely down and removing the whole motor and transmission assembly out of the unit. It may be possible to get at the seal without doing this but I'm not 100% sure. To get the whole unit apart I did the following: Remove the front panel by removing the two screws located at the very bottom of the panel and lifting up and out .Remove the top/lid by removing two screws underneath the top toward the front, and disconnecting lid switch, or i found it easier to just unscrew and remove it, then lift off the top/lid assembly. Remove the agitator cap and the agitator. Remove the splash cover (this is not easy- I popped each tab with a flat screw driver- the ones at the rear were very difficult). I tried to remove the fill spigot but could not get at one of the screws so getting the splash cover out was not as easy as it could have been. Remove the bolts in the bottom of the tub and lift it out. Unhook the drain hose and the level or "pressure tube". Remove the 3 large and 3 small springs from the motor assembly ( I needed a strong spring hook but all I had was vice grips, they work but it was not easy). remove any other wires etc. (mark things with tape and matching numbers if needed) and pull out the whole barrel and motor assembly. Unbolt the splash tub and remove, unbolt the trunnion and remove. And finally replace the seal. Reassemble in reverse order. Important!! Clean shaft well (I used some 300 grit fine sandpaper to remove the little bit of rust scale that had accumulated) and lubricate everything. be very careful when reassembling, as to not scuff up the seals at all. I used a silicone spray. This might not be the best thing for the job but I know at least not to use anything petroleum based such as WD-40 when you are lubricating rubber or plastic. Reinstalling the springs was very difficult and again a spring hook would have been great. Everything else went together reasonably easy. The unit works fine now. many thanks to the websites I researched to get this done.

After removing the front of the washer, I used slip joint pliers for the hose clamps, then a screwdriver for the mount bolts and replaced the pump motor in reverse order. The pump was ordered on line on a Friday before 10am and was delivered on saturday moring by FedEx. I could not have expected such fast and efficent service!
Great Job!!