LWS55AW-PLWS55AW Speed Queen Washer - Instructions

We did not have instructions on how to remove broken agitator. Looking online, we found easy instructions but found it difficult to remove the agitator even though it was supposed to be an easy task.
Our particular model was supposed to "pop" off with little resistance. Not so!
It took some stong muscle and will power to remove the part but putting the new agitator on was simple.

remove front cover disconnect water supply remove hose clamp,take drain line replace with new hose reconnect water supply replace front cover job complete.

Disassembled washer as per directions with seal kit. Removed inner tub. Cut both tub shaft bearing in half; punched out from outter tub. Installed new bearings using .5 inch threaded rod, washer and bolts. Installed new seal on inner tub shaft. Installed inner tube. Re-assembled washer.

Since the agitator and bell housing seperated as once piece from the drive shaft I didn't have to remove them and the schematic showed how the agitator snapped on to the bell housing and the parts I needed for the fix. The new seal went on with no problem, I just used some of the supplied grease on the tight spots. The hardest part was attaching the bell housing. It came to within an inch of the top of the shaft with no problem with a rubber hammer. But the top screw shroud broke when I tried to hammer it the rest of the way using a wood dowel and a block of wood. I couldn't even get the threads of the supplied screw to even touch the drive shaft. So I bought a longer (1 inch) cap screw from the hardware store and added a washer and suplied ring. After torqing it to 5 ft-lbs instead of the 10-20 the plastic beneath the screw was looking kind of thin and stressed and I was afraid of it breaking through or the screw snapping off in the shaft, so I left it alone and used some silicone caulk to seal in the plug that goes in on top of the screw since the side of the shroud broke off. I slipped on the agitator and am testing a load now as we speak. If I get ten more years out of the washer it will definitely be worth the $100 in parts and shipping !

a nail from my pocket fell out and was in one of the holes in the in the tub and bound up the tub.when it wold try to spin.ordered the belt and had to order a pump also it melted the bearing in it

Removed the front panel, could see water leaking from the tub area near the shaft in the center of the machine. Dripping out once the water level reached the hub. Swing the top up, remove the large plastic ring at top of tub. remove the top of the agitor, pulls off easily. Remove the agitator with a firm pull up, not as easy but does come off. Removed the 4 bolt holding the tub. 2 broke off, but not to worry, the new kit has a complete hub. Pulled off the bell seal, pry up. Used an impact gun with 1-1/2" socket to remove the nut. The hub was frozen to the shaft. Tried a puller but ended up breaking the hub. I finally cut it off in pieces and pryed it off (the hardest part of job). Cleaned up the spline with a small file and patience. Installed the new seal kit. Ended up buying the M800 3M sealant on line. I went this far, another $40 for that. Fitted it all back up per instructions. No leaks. All good.

My Amana washing machine burned up a second belt in about three weeks. Prior to that, the spin cycle was very loud. Online research revealed the problem was most likely the hub bearing. I ordered a new bearing, belt and hub and seal kit. The repair is a difficult one as the parts have been on the tranmission shaft many years with the mounting corrosion and mineral build up. I was able to pull the agitator off with no problem. The drive bell would have been easier to pull had I used a gear puller but did not own one. I use two crow bars to lift it off the shaft and I knew I'd be replacing it anyway so was not concerned about damaging it although I didn't. The most difficult part to remove was the large hex nut. I didn't want to purchase the tool to remove it so I used an open end adjustable wrench adn a hammer to remove it. However it took many hours of soaking the nut in sprayed on WD-40 to loosen it. For a while I thought it wasn't going to budge. Oh and btw, the nut comes off counterclockwise on this model. This is important. Other makes of washers have left handed threads, requiring clockwise removal, but this one does not. The hub assembly was pulled using the crow bar method. Again, it was going to be replaced anyway. The lint filter was cleaned and reused. The remainder of the dissassembly went OK using the directions in the repair manual. http://www.scribd.com/doc/8677902/Amana-Top-Load-Washer-Service-Manual. Reassembly went fine using the repair manual accept that the new drive bell was much more difficult to drive onto the shaft than I thought it would be. I eventually got it on using my shop vac rigid tube to go around it and hammering on a block of wood placed on top of it. I also used this shop vac tube to seat the seal that goes on the shaft just before the drive bell. It was the perfect tool for it as I wasn't going to purchase the special tool suggested in the repair manual. I'd already purchased $185 in parts. The kits come with grease but not the anti seizure compound or the industrial sealant needed. The anti seisure compound can be purchased from an auto parts store. It's not expensive. The industrial sealant is expensive. After researching what it was and why it was needed, I took a chance on silicone sealant. I'm not suggesting it is a good substitute but my washer has not leaked after 5 loads. Plus the sealant is really a backup to the main seal that goes on the transmission shaft before the hub assembly. But I'm pleased overall with the parts and accompanying directions and the washer is working great, spinning quietly. This is not an easy repair. It takes patience and a place to work on it. Frankly, with other things to do as well as go to work, it took me four days to complete, mostly due to the difficulty in removing the large hex nut. It might be worth investing in the removal tool if you're unsuccessful using home tools. Good luck.

Just as everyone else explained, disconnect power and water supply, lift top of machine to get to part, disconnect old part and replace exactly with new, hook water and power supply back up and you're done. I was pleased and proud to have done it under 30 minutes (girl power!!) and that included start to finish.

Replaced water inlet valve with the water inlet valve kit. We ordered it on Monday morning. The part arrived the next day, Tuesday. New inlet valve was put in on Wednesday. It took less than 15 min., and my washer was working! Very impressed!

Purchased x4 new adjustable legs. Leaned the washer back and held in place with block of wood. Loosened the two older front legs with an adjustable wrench because they had a locking nut and replaced with new legs. Repeated process on back side of washer. Once all the new legs were installed leveled the machine adjusting the legs if necessary.

Removed the plate screws. Found valve, unplugged wires, removed hose and replaced reattaching everything. Replaced plate. Done

I read everyone else's stories and tried this for myself. I am by no means a handy person. This was extremely easy and took me about 10 minutes. I would suggest to everyone to try this for themselves if they have the same problem as I did. Anyone can do this.

Took off part and replaced it very easy instructions.

The new hose was exactly like the one I removed. It was simply a matter of putting the new hose through the back, replacing the hose clamp, take the piece off the old hose that makes the bend in the hose to go in the wall drain. Replace the lower front panel with two screws and I was done.

Replaced the inlet mixing valve. Two screws and two electrical plug ins and you are done.