SWFX71NN3050 Speed Queen Washer - Instructions

Replaced heating element,thermal fuse,cycling thermostat,thermal cut off kit and don't forget to flip your dryer fuse in the breaker panel that was a big one for me. Hope this helps you.

Followed instructions, installed part, apparent after turning on dryer and still no heat we didnt fix the problem yet, will try another different part at a later time. At least we know we will have a fresh heating element.

I first disconnected the power, dryer vent hose, back panel, disconnected power leads to heater element. Next removed top screw to the heater box, slid the box up and away from lower mount. At this point I was able to remove 1 ea lower screw holding heater element in place. Removed heater element and installed new element. Put everything back in reverse order and started dryer. (Note: Be sure dryer door is closed prior to starting dryer)Yep, I screwed that up. It no "worky" when dryer door is open. Once the door was shut, it worked like a champ.

Unplugged dryer. Removed back panel from dryer. Using needlenose pliers, disconnected wires going into heating element housing cover. They basically just unplug. You have to wiggle them a little with the pliers to get them unplugged. The housing cover is the large metal piece on the right side of the dryer. Kind of looks like a catalytic converter from a car. Popped off housing cover by putting a large screw driver behind it and gently prying forward. The top came loose from the dryer and I then lifted it up off the two tabs holding it at the bottom. I then unscrewed the one screw holding the element to the bottom of housing cover. I slid the element out, inserted the new element, put the screw back in place and then put the housing unit back in place over the two tabs. I replugged all of the wires into the housing unit, replaced the back cover on the dryer and plugged the dryer into the wall receptacle. I turned the dryer on and it heated up right away. I have since dried several loads and it is working perfectly. By the way, I am a 65 year old housewife. If I can do it, anyone can.
Mary McCarthy
Jacksonville, FL

First of all the instructions with the part were not very plain to understand so I returned to the web site and read some of the other custormers instructions and was able to figure out how to replace the part. Just had to unscrew the back panel and remove the screws from the heating element housing and then I took the screws out of the lint compartment so I could remove the whole housing to remove the screw that held the heating element to the housing and was easy to cut the eletric wire and conect the new wires and twist the new wire cap on and put everything back together. I was so glad that when I turned the dryer back on I had heat. I am 57 year old women and If I can figure of how to fix my ole dryer than I think anyone can. When I can I will order the part for a new timer. And I hope that my dryer will last another 10 years.

First, I tilted the dryer forward and leaned it carefully against the wall to gain access to the back cover. Used a nut driver to remove 5 screws holding the back cover. Tested the heating element using a multi-meter and it showed an open circuit. I tested the thermostat and a few other switches and they were all ok, so I knew for sure it was the heating element only. The part arrived in 2 days which was great, cause with 3 kids, dirty clothes pile up fast. I pulled several set of wires for the thermostat, switches etc. marking the wires to make sure I put them back correctly. I loosened the heating element housing by removing one screw at the top (with a clip attached) and one at the bottom. I pulled the housing out, then pulled the element out of it's cover and slid the new one in back in it's place. Screwed the cover back in, put the wires back into place and replaced the back cover. I made a few rookie mistakes during the process, but we won't discuss those. Anyway, bottom line is...the dryer worked perfectly...laundry time.

Checked fuses, breakers, etc. with multimeter to make sure nothing else was broken, then removed the heat element and - voila - it had snapped in the middle (should've done this first!). Searched the Web for the best price; 30-45 minutes removal, diagnosis, etc. 15 min to fix it

I read all the other stories and thought this would be a piece of cake. No one mentioned that you had to remove a small piece a metal holding the element casing from underneath the top of the dryer. Very hard to reach that screw. Then no one mentioned that the element casing had to be pulled out of the hole at the back of the dryer before you could remove the element. If i had known these things ahead of time, it would have been a simple project. After all is done, the element was not the problem. Now i think i need a thermostat. lol!!!!!

ordered on-line monday recieved on tuesday wife drying clothes tuesday evening--------just took out old element and hooked up new one --- very easy

Remove screws at lint filter, open top of dryer. Remove hex screw holding top of element casing. Slide dryer away from wall, remove 5 hex heads from rear panel, exposing element casing. Remove two screws holding sensors, and move aside. Lift dryer casing slightly and pull towards you to disengage from rear panel. Turn over and remove srew holding element to casing at bottom. Slide element out, and unplug two wires, noting position of each wire. Reverse procedure to reinstall element. Dryer works better than it has for years !

According to previously submitted instructions. toughest task was replacing the tiny screw at the bottom of the heating element housing. Felt good to plug it in, start it up and voila, heat. thank you for the part.

Took off the back panel, and with a little prying got the heating element case off (it's on the right of my LE5800XK). Replaced the heating element, put everything back, and voila, works better than before.

Fairly straight forward except for hidden 5/16 self tap screw coming from back side of heat ducting that is welded to drier. You have to remove this by feel and restart by feel which may be difficult for some. This screw holds the element to the heat duct. It has to come out

My son did the repair and thought it went very well. You saved me about $400 to $800 in that I didn't have to buy a new one. You got this part to me in 48 hours and I appreciated your timely manner. Your service is great! Thanks MZ

Removed the back,and a few screws through the top that held the filter sleeve in.
That allows enough room to reach in under the top, and unscrew the one screw that holds the element housing in place at the top.
Lifted the housing out after disconnecting the wires to the sensors and element.
Removed the element and replace it with the new one.
All of the electrical connectors slid right on the new element and put it back together.
Everything works fine.
Spent more time cleaning debris out of the dryer while I had it apart than replacing the part.
As usual Parts Select came through with the right part delivered to my door the next day, after ordering.
Thanks