SWFX71QN3000 Speed Queen Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- KEN from OXFORD JUNCTION, IA
- Parts Used:
- WP4391960
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Heating Element Bad
Fairly straight forward except for hidden 5/16 self tap screw coming from back side of heat ducting that is welded to drier. You have to remove this by feel and restart by feel which may be difficult for some. This screw holds the element to the heat duct. It has to come out
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Kettering, OH
- Parts Used:
- WP4391960
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dryer not hot enough to dry a load of clothes
My son did the repair and thought it went very well. You saved me about $400 to $800 in that I didn't have to buy a new one. You got this part to me in 48 hours and I appreciated your timely manner. Your service is great! Thanks MZ
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Samuel from Robertsville, MO
- Parts Used:
- WP4391960
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
No Heat, broken element
Removed the back,and a few screws through the top that held the filter sleeve in.
That allows enough room to reach in under the top, and unscrew the one screw that holds the element housing in place at the top.
Lifted the housing out after disconnecting the wires to the sensors and element.
Removed the element and replace it with the new one.
All of the electrical connectors slid right on the new element and put it back together.
Everything works fine.
Spent more time cleaning debris out of the dryer while I had it apart than replacing the part.
As usual Parts Select came through with the right part delivered to my door the next day, after ordering.
Thanks
That allows enough room to reach in under the top, and unscrew the one screw that holds the element housing in place at the top.
Lifted the housing out after disconnecting the wires to the sensors and element.
Removed the element and replace it with the new one.
All of the electrical connectors slid right on the new element and put it back together.
Everything works fine.
Spent more time cleaning debris out of the dryer while I had it apart than replacing the part.
As usual Parts Select came through with the right part delivered to my door the next day, after ordering.
Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- george from granby, CT
- Parts Used:
- WP4391960
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
heating element broke
ordered on-line monday recieved on tuesday wife drying clothes tuesday evening--------just took out old element and hooked up new one --- very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Bradenton, FL
- Parts Used:
- WP4391960
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Dryer stopped heating
Remove screws at lint filter, open top of dryer. Remove hex screw holding top of element casing. Slide dryer away from wall, remove 5 hex heads from rear panel, exposing element casing. Remove two screws holding sensors, and move aside. Lift dryer casing slightly and pull towards you to disengage from rear panel. Turn over and remove srew holding element to casing at bottom. Slide element out, and unplug two wires, noting position of each wire. Reverse procedure to reinstall element. Dryer works better than it has for years !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Mableton, GA
- Parts Used:
- WP4391960
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Dryer stopped heating
Super easy!
-unplugged
-removed the 6 screws in the rear
-pulled off the back panel
-unplugged the 2 wires attached to the heater element (note which one connects to where)
-remove dryer filter and the 2 top screws that next to it
- lifted the top up
- there is one screw at the top of the heater element casing that needed to be removed.
- poped the heater casing away from the dryer.
then pulled it out from the bottom
- removed the one screw holding the heater element in the case, and slide it out
-slide the new one in, and put the screww back in
-pushed the heater casing back up in the dryer and connected the 2 element wires.
-slide the heater casing in the 2 slots and pushed it backing to the dryer at teh top.
-screwed the on screw back in at the top of the casing.
- put the dryer top back in place and 2 fliter screws back in.
- reattached the back panel. and plugged back in.
- viola...
-unplugged
-removed the 6 screws in the rear
-pulled off the back panel
-unplugged the 2 wires attached to the heater element (note which one connects to where)
-remove dryer filter and the 2 top screws that next to it
- lifted the top up
- there is one screw at the top of the heater element casing that needed to be removed.
- poped the heater casing away from the dryer.
then pulled it out from the bottom
- removed the one screw holding the heater element in the case, and slide it out
-slide the new one in, and put the screww back in
-pushed the heater casing back up in the dryer and connected the 2 element wires.
-slide the heater casing in the 2 slots and pushed it backing to the dryer at teh top.
-screwed the on screw back in at the top of the casing.
- put the dryer top back in place and 2 fliter screws back in.
- reattached the back panel. and plugged back in.
- viola...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from littleton, CO
- Parts Used:
- WP4391960
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Stopped heating
Replaced heating element,thermal fuse,cycling thermostat,thermal cut off kit and don't forget to flip your dryer fuse in the breaker panel that was a big one for me. Hope this helps you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Herington, KS
- Parts Used:
- WP4391960
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
install a new heating element
First of all the instructions with the part were not very plain to understand so I returned to the web site and read some of the other custormers instructions and was able to figure out how to replace the part. Just had to unscrew the back panel and remove the screws from the heating element housing and then I took the screws out of the lint compartment so I could remove the whole housing to remove the screw that held the heating element to the housing and was easy to cut the eletric wire and conect the new wires and twist the new wire cap on and put everything back together. I was so glad that when I turned the dryer back on I had heat. I am 57 year old women and If I can figure of how to fix my ole dryer than I think anyone can. When I can I will order the part for a new timer. And I hope that my dryer will last another 10 years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Twentynine Palms, CA
- Parts Used:
- WP4391960
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The dryer was not getting hot
I removed the back panel and took the 2 screws out at the lint screen, lifted the top back so I could remove the bracket holding the heating element can. After this was completed I was able to remove the heating element and install the new one, I had to cut the old connectors off and wire nut the new connector together. After this part was completed I reinstaaled the heating element can, secured the top back down,reinstalled the the back panel and pluged it in and wa-la it worked. I also wanted you to know that your prices are about $ 7.00 less than a few of the other part sites I checked on line and one of the sites even said that the part I needed was no longer available. I am sure glad that I kept looking and found your site because you saved me from buying a new dryer, thank you and if I get asked where to get parts I will recommend PARTSSELECT.COM.
Fred
Fred
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from New Milford, CT
- Parts Used:
- WP4391960
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dryer stopped heating up
Located heating element at PartSelect easily.Worked perfectly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from Hugo, CO
- Parts Used:
- WP4391960
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
No heat
Took off the back panel of the dryer. Removed the screw holding the drying element in only to discover it would not fit out the bottom of the case holding it because it was too close to the bottom of the dryer. Had to take off the top of the dryer and remove the casing, remove the element, replace it and put the casing back. Not too difficult, only two wires and one screw. Did make a couple of rookie mistakes making me backtrack and redo a few things but nothing major.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from New Smyrna Beach, FL
- Parts Used:
- WP4391960
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Dryer produced NO HEAT.
Following one of your site's more detailed repair suggestions, I began checking the higher percentage likelihood of failures and stepped-through to what my initial suspicion was: The Heating Element (13% ??). I first checked the fuse (rated at 73% probability) (both thermostats were rated very low as possible problems) and immediately went to the element. The failure was discovered in short order by checking continuity along the coils until a physical break appeared. The most helpful advice I received was from the pointers to remove the two screws attaching the heat vent/filter plenum in order to lift the dryer top and access the anchor screw attaching the top of the heating element box. I was over-joyed to find that the 29-year-old part number I entered, with the replacement number your system displayed, was PRECISELY the physical size and shape of the original heating element when I opened the package !! To borrow a page from the old PGA TV ad: "(You) guys are good." Many thanks !!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- bern from levittown, PA
- Parts Used:
- WP4391960
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
very low heat
it was easy to replace the element
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rubene from Daleville, AL
- Parts Used:
- WP4391960
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
dryer wouldn't heat up
unpluged the unit removed exaust, pulled away from wall about 18 inches. Then leaned unit face down, remove back shield/cover also remove he two wires to elements. At the top of housing where element is in there is a screw that needs to be removed, then lift housing element is in side. Slide foward and lift to remove,to replace go in reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Hampton, VA
- Parts Used:
- WP4391960
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
heating element burned out
checked element leads with voltmeter (set on ohms) - no continuity. - biggest problem is that the can over the element is screwed in from the back - you have to take out the lint filter and unscrew the two screws beneath it then pry open the dryer top - then you can unscrew the one screw holding the clamp on the can. This seems to be a feature added just so people would call out for repair - I can't imagine how it would have been quicker or easier to manufacture it this way. The can just pulls out and is hinged from the bottom - you may have to jerk on it after you remove the clamp. (pull from the top). One screw holds the element in. That is it for the replacement. Now the stupid part - check to see if the exhaust vent is clogged. I pulled several cubic feet of lint out and didn't bother to put a mask on and almost choked to death. I recommend you to get a dust mask before cleaning a tube longer than 8 feet.
Was this instruction helpful to you?
Thank you for voting!