WF330ANBXAA Samsung Washer - Instructions

Take pics every step, easier re-assembly. Dismantled washer keeping bolt/screw section removed compartmentalized in a tackle box in the order of removal. Replaced drum support, bearings, seal, old blots. Too much to write but I was able to do it all in about 4 hours once all the parts finally came in.

Removed the 3 screws that hold the bottom front panel in place. Removed the 3 screws that hold the door latch in place and pulled out on the bottom of the door which wasn't very much and slid the door latch out to get to the wire connections. Connected the wires to the new latch and pulled out bottom again and put the latch back into place and put the 3 screws back in. Note: make sure you unplug the washer so you don't have a chance to get shocked. Level of difficulty was pretty easy.

First unplug or turn off thee circuit breaker. Then remove the two screws to the top cover. Slide the cover back about three inches then remove the cover. Next take out the screw to the old sensor. Then unplug the electrical connection by squeezing and the pulling to disengage. Now set the old unit aside. You then grad your eight inch wire tie and hold the with flat side to the right and just to the right of the screw hole for the bracket is a square hole. Feed to wire tie into the square hole with your left hand then loop down left side of the end of new sensor and back up threw the square hole and tighten with the pliers. Your new sensor will be positioned just like it was mounted to the metal bracket. And pretty ridged. Now connect the vacuum hose and electrical connector.

Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.

easy process: troubleshoot problem on website-- order part--get part--watch "how to replace"video on you tube-- get it done with only a screwdriver--go out for movie and dinner with $$ saved.

When I looked at the website for latch repair they showed a video (can't remember which brand but not Amana) where you had to take off the top and front of the washer to get at the latch part on the washer. For the Amana I had, you simply had to pull out a portion of the rubber gasket held onto the washer by a wire/spring combination (you can take the wire off) to get at the latch assembly. You could then undo the three screws holding the latch to the washer, pull it out and unplug the three wiring connections to remove the old latch. Then plug connections into the new latch, reinstall, tighten screws and fit gasket and wire/spring assembly back together. Much easier than going thru the top and front of the washer!

Strip clean and replace

Unplug machine,remove three screws that hold on top cover.
Unplug latch switch assembly,then open front door of washing machine, remove three screws which hold latch
switch. Install in reverse order.

I had to pull the washer out from the wall. SInce it is in front of the door going out into the garage made it dificult getting tools. I had to lay on my side doubled up in order toget to the hose. I used a bit extention so that I could get the clamp loose. Cut the time in half by using a drill with a phillips head screw bit. The only real hard part was getting the new one up tight on the drain. Used a heavy duty screw driver to push it up so the clamp would bite.

We followed another very helpful repair story. Unplug machine. Unscrew top back screws, remove top of washer. Reach inside from the top in the front of the machine. Remove screws holding latch in place, unplug the three plugs attached to latch. Replace with new door latch, screw it in place, replug the three plugs, put top of machine back on, replace screws on back and your'e done! Works great! Job made easy thanks to others helpfulness!

The washer tech manual stated to: 1) remove the top, 2) control console, 3) front below the door (front load washer), 4) remove the retaining wire, 5) pull back the rubber bellows, 6) remove the three screws and remove the door latch/lock assembly. I discovered that steps 1 through 3 are not required to replace the assembly. Installation is the reverse of steps 4 through 6. That was easy. The difficult part was figuring out how to reset the pressure switch so the drain pump would not start every time you reconnected to the power supply (pressure switch thinks the washer still contains water). With the power disconnected, I disconnected the pressure switch from the central control unit. Then I reconnected the power supply and pressure switch. That reset the pressure switch solved the problem with the drain pump. Washer works fine now.

This took ten minutes .... super easy .... DO IT YOURSELF!!!! About 75.00 with shipping ... can only imagine this woulkd have been 250 to 300 to have somebody com e onsite.

I went to Maytag.com and typed in my model number and it came up with different parts I found the glass part I needed and ordered it. I received it in like 3 days. I had a phyllips screw driver and it the removal of the base around the glass replace the glass and screwed it right back on and started washing clothes. No leaks at all. I am a woman and proved woman can do the same things a man can do but quicker.LOL

Removed top cover. Manually opened door through top cover opening. Removed 3 screws at front holding assembly. Removed 3 harnesses attached to assembly. Replaced with new assembly and screwed back in. Replaced harnesses. Certainly an easy DIY job.

The product came on time and was perfectly rapped , it took me 15 mins to install after watching you tube videos on front loader washer . I was happy I didn't have to call a service man in . . . .