Models > WF363BTBEUF

WF363BTBEUF (A2-0001) Samsung Washer

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for WF363BTBEUF

Viewing 8 of 8
Keep searches simple, eg. "belt" or "pump".
This part is used for the shaft on rear of the tub. Sold individually.
In Stock
Order within the next 12 hrs and your part ships today!
In Stock
Order within the next 12 hrs and your part ships today!
One solenoid valve for hot water
In Stock
Order within the next 12 hrs and your part ships today!
In Stock
Order within the next 12 hrs and your part ships today!
In Stock
Order within the next 12 hrs and your part ships today!
In Stock
Order within the next 12 hrs and your part ships today!
In Stock
Order within the next 12 hrs and your part ships today!
$211.80
In Stock
Order within the next 12 hrs and your part ships today!
In Stock
Order within the next 12 hrs and your part ships today!
The pressure switch senses and controls the water level in the washer.
In Stock
Order within the next 12 hrs and your part ships today!
In Stock
Order within the next 12 hrs and your part ships today!
Assembly BOLT;SWF-P12,MOTOR/
In Stock
Order within the next 12 hrs and your part ships today!

Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Problems and Symptoms for WF363BTBEUF

Viewing 2 of 2
Will not drain
Fixed by these parts
Fixing
How to fix it
Leaking
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Samuel from NEEDVILLE, TX
Parts Used:
DC60-40137A
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Screw drivers, Socket set, Wrench set
Washer making noise a snow smoking.
Take pics every step, easier re-assembly. Dismantled washer keeping bolt/screw section removed compartmentalized in a tackle box in the order of removal. Replaced drum support, bearings, seal, old blots. Too much to write but I was able to do it all in about 4 hours once all the parts finally came in.
9 of 21 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Fredric from ROCKMART, GA
Parts Used:
DC96-01703B
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
The water level was lower than normal.
First unplug or turn off thee circuit breaker. Then remove the two screws to the top cover. Slide the cover back about three inches then remove the cover. Next take out the screw to the old sensor. Then unplug the electrical connection by squeezing and the pulling to disengage. Now set the old unit aside. You then grad your eight inch wi re tie and hold the with flat side to the right and just to the right of the screw hole for the bracket is a square hole. Feed to wire tie into the square hole with your left hand then loop down left side of the end of new sensor and back up threw the square hole and tighten with the pliers. Your new sensor will be positioned just like it was mounted to the metal bracket. And pretty ridged. Now connect the vacuum hose and electrical connector.
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Hilda from YONKERS, NY
Parts Used:
DC97-16596A
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set
The boot had a crack, where the leak was.
Took off the front part of boot on the door, continued to take out the front and top off to washer Faisal.
Removed weights and boot connected to the drum. Installed new boot and leeks was gone.
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!