Models
>
WA50K8600AV
WA50K8600AV (A2-0011) Samsung Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for WA50K8600AV
Viewing 5 of 5
Keep searches simple, eg. "belt" or "pump".
$89.85
The drain pump assembly removes water from the washer during the drain portion of the cycle.
On Order
In Stock
In Stock
$44.36
The suspension rod supports the washer tub and keeps it stable during unbalanced loads. DF10.5@250RPM,K0.41,L715
In Stock
In Stock
$87.25
The thermistor monitors and helps regulator the water temperature in the washer.
In Stock
In Stock
In Stock
In Stock
In Stock
The levelling leg rubber pad covers and cushions the bottom of the levelling leg.
In Stock
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for WA50K8600AV
Viewing 1 of 1
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dieter from CHICAGO, IL
- Parts Used:
- DC97-19289F
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Easy instal, taking off entire back panels of appliance is required
Shut off water and electrical supply to appliance, take water supply hoses off to allow for proper access to back of machine.
Take off back panels of appliance. Disconnect two hoses from pump. Take out two screws which attach pump to washer body. Detach wiring which connects pump to control unit ( that takes a little time). Install p ... Read more ump in designated location, connect hoses, connect wiring to control unit, connect appliance to powere source, test run to make sure everything works properly, make final detailed wire connection Pump to control unit, install back panels, Connect water supply hoses .....and be proud of yourself!
Take off back panels of appliance. Disconnect two hoses from pump. Take out two screws which attach pump to washer body. Detach wiring which connects pump to control unit ( that takes a little time). Install p ... Read more ump in designated location, connect hoses, connect wiring to control unit, connect appliance to powere source, test run to make sure everything works properly, make final detailed wire connection Pump to control unit, install back panels, Connect water supply hoses .....and be proud of yourself!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Medina, OH
- Parts Used:
- DC97-19289F
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Top Load washer would not drain to complete spin cycle.
Though I could hear and feel the drain pump running, the washer would not drain. This model does not have a filter for the drain pump. I lowered the discharge hose from the stand up pipe on the wall, and lowered it to the floor. Water ran right out, so no blockage in the drain system. After removing the inlet and outlet hoses to the pump,
... Read more
a quick inspection showed the impeller on the motor was off the shaft and flopping around. Bingo, motor runs but cant pump.
Ordered from Partselect and received in ONE DAY. I really didn't want to go back to it that soon, but they certainly did their part. Ha. Thank you all. Greg
Ordered from Partselect and received in ONE DAY. I really didn't want to go back to it that soon, but they certainly did their part. Ha. Thank you all. Greg
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tommie from MURFREESBORO, TN
- Parts Used:
- DC66-00887B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Pulsator cap broke off.
The cap was easily replaced by hand and pops right in place.
Was this instruction helpful to you?
Thank you for voting!