Models > WA456DRHDSU > Instructions

WA456DRHDSU (AA-0002) Samsung Washer - Instructions

Jump to:

All Instructions for the WA456DRHDSU
1 - 5 of 5
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Dieter from CHICAGO, IL
Parts Used:
DC97-19289F
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Easy instal, taking off entire back panels of appliance is required
Shut off water and electrical supply to appliance, take water supply hoses off to allow for proper access to back of machine.
Take off back panels of appliance. Disconnect two hoses from pump. Take out two screws which attach pump to washer body. Detach wiring which connects pump to control unit ( that takes a little time). Install pump in designated location, connect hoses, connect wiring to control unit, connect appliance to powere source, test run to make sure everything works properly, make final detailed wire connection Pump to control unit, install back panels, Connect water supply hoses .....and be proud of yourself!
8 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Greg from Medina, OH
Parts Used:
DC97-19289F
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Top Load washer would not drain to complete spin cycle.
Though I could hear and feel the drain pump running, the washer would not drain. This model does not have a filter for the drain pump. I lowered the discharge hose from the stand up pipe on the wall, and lowered it to the floor. Water ran right out, so no blockage in the drain system. After removing the inlet and outlet hoses to the pump, a quick inspection showed the impeller on the motor was off the shaft and flopping around. Bingo, motor runs but cant pump.
Ordered from Partselect and received in ONE DAY. I really didn't want to go back to it that soon, but they certainly did their part. Ha. Thank you all. Greg
6 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gary from CENTER HARBOR, NH
Parts Used:
DC31-00153A
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
Washer stopping in the rinse and spin cycle
Tipped the washer up on a couple of chairs. Pulled the motor apart in three pieces and replaced the Hall Sensor. Error code lead me right to the problem and solution.
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Alpha from JACKSONVILLE, FL
Parts Used:
DC97-19289F
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers
Washer will not drain
Went to YouTube video and followed instructions.

Hardest part was making sure water from hose does not flood floor while taking it off from water pump and letting water drain in bucket.

See YouTube video

https://youtu.be/oOnxbj-unfc?si=OFFwOcNiIymh_9b-
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from HERNANDO, MS
Parts Used:
DC97-16979A
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Drain hose was cracked and leaking.
Squeezed clamp with fingers to remove old drain hose. Put clamp on new replacement hose and slid over drain pipe and released clamp. Less than a minute. Hose was exact replacement part.
2 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the WA456DRHDSU
1 - 5 of 5