WF219ANBXAA Samsung Washer - Instructions

Unplug machine,remove three screws that hold on top cover.
Unplug latch switch assembly,then open front door of washing machine, remove three screws which hold latch
switch. Install in reverse order.

First unplug or turn off thee circuit breaker. Then remove the two screws to the top cover. Slide the cover back about three inches then remove the cover. Next take out the screw to the old sensor. Then unplug the electrical connection by squeezing and the pulling to disengage. Now set the old unit aside. You then grad your eight inch wire tie and hold the with flat side to the right and just to the right of the screw hole for the bracket is a square hole. Feed to wire tie into the square hole with your left hand then loop down left side of the end of new sensor and back up threw the square hole and tighten with the pliers. Your new sensor will be positioned just like it was mounted to the metal bracket. And pretty ridged. Now connect the vacuum hose and electrical connector.

Strip clean and replace

I had to pull the washer out from the wall. SInce it is in front of the door going out into the garage made it dificult getting tools. I had to lay on my side doubled up in order toget to the hose. I used a bit extention so that I could get the clamp loose. Cut the time in half by using a drill with a phillips head screw bit. The only real hard part was getting the new one up tight on the drain. Used a heavy duty screw driver to push it up so the clamp would bite.

My husband simply removed the old sensor and put the new one in. It was not difficult.

Take pics every step, easier re-assembly. Dismantled washer keeping bolt/screw section removed compartmentalized in a tackle box in the order of removal. Replaced drum support, bearings, seal, old blots. Too much to write but I was able to do it all in about 4 hours once all the parts finally came in.

I followed the guy on the video. The only parts that were tough was having the right tools and having enough space to put the new part in. The part was only 70 dollars and I was so proud that I could do it. I am not very handy so if I can do it then anyone can. Plus I saved some money!

We followed another very helpful repair story. Unplug machine. Unscrew top back screws, remove top of washer. Reach inside from the top in the front of the machine. Remove screws holding latch in place, unplug the three plugs attached to latch. Replace with new door latch, screw it in place, replug the three plugs, put top of machine back on, replace screws on back and your'e done! Works great! Job made easy thanks to others helpfulness!

first of all, I am not at all handy, so that fact that I could do this at all is pretty amazing. I watched the video and it was very good. At first all went smoothly...I got the top off, the control panel off and the detergent drawer out. Then I ran into problems, three of the six screws holding on the front panel wouldn't come out. I sprayed Liquid Wrench on, waited for a while, still wouldn't come off, then I tapped them with a hammer, still wouldn't unscrew. But I was able to access the door latch from the top rather than the side...a little tight and awkward, some swearing was required, but it worked. Machine now working like a charm, yay!

It is very easy. Unplug from the wall. Take out the two screws from the back that holds on the top panel. Unscrew the three screws inside the door by the latch. Reach inside the washer from the top and unplug the three plugs on the latch part. Then plug in the new part , put the three screws back in. Then put the top panel on. Plug in and magic. It works!

I read what others wrote and put two and two together and 15 mins. later I was up and running. lots to take apart but it all went smooth and no left over parts washer runs like new again

The washer tech manual stated to: 1) remove the top, 2) control console, 3) front below the door (front load washer), 4) remove the retaining wire, 5) pull back the rubber bellows, 6) remove the three screws and remove the door latch/lock assembly. I discovered that steps 1 through 3 are not required to replace the assembly. Installation is the reverse of steps 4 through 6. That was easy. The difficult part was figuring out how to reset the pressure switch so the drain pump would not start every time you reconnected to the power supply (pressure switch thinks the washer still contains water). With the power disconnected, I disconnected the pressure switch from the central control unit. Then I reconnected the power supply and pressure switch. That reset the pressure switch solved the problem with the drain pump. Washer works fine now.

Checked owners manual for diagnostics. Pointed to door lock mechanism, so we replaced. didnt work. Went online to Just Answers.com, chatted with pro named Mike(for the fee of $25) and without getting full description, he told me to replace pressure sensor. Bought one here for $50, replaced it, and still the problem lingered. Called a real Technician to the house, for $90, and he spent 4 minutes looking and tapping, and voilla, it worked. Turns out it was a stuck relay on the control board, and the tapping loosened it. He told me I may have trouble with it in the future. If so, I would buy one here. Thanks

Used online video which was really good. After changing the lever, I realized I needed to order a new latch because it was broken also.

Unplug electric. Open door. Peel rubber bladder back from washer door seal enough to expose wire retension ring. Remove three screws that hold door latch. Remove latch. Remove three wire harnesses. With new latch, reattach wire harnesses. Insert latch. Secure to machine with the three screws. Refit door seal and secure with retension ring. Plug in electric. Done.