RTW4100WQ1 Roper Washer - Instructions

Ordered and replaced the sensor. Fairly simple. Washer runs good now. Thank you!

Removed control assembly found lid switch. Had to unscrew ground wire from warsher popped clip on old switch came right out. Had to play with lid in order to remove. Popped new switch in screwed ground wire. Reinstalled control panel,plugged in and the way it went. Trouble shot with parts direct made it easy and saved me 350 dollars(new washer)

Well, after resolving Part Select (PS) shipping issues (PS sent me two refrigerator glass shelves instead of a Tub Spring); And as it turns out they sent me the wrong part for the suspension pads, which I have returned for credit. It takes 3-4 weeks to obtain your credit BTW.

Well after removing the cabinet, agitator, wash basket, plastic tub, all 5 springs, & pump suction line, I was able to access the Tub wear pads and suspension pads. As it turns out the suspension pads looked good.
Thank God, as PS had sent wrong parts. I replaced the wear pads, the 5 springs, and reversed the disassembly process. Took about 6 hours.
But washer works fine now, still vibrates, but does not walk across floor any more.

I had no idea what the problem was...other than the drum would not spin and it made a horrible noise...so I figured the motor was still good. I figured the repair man would charge me $200 and a new washer is $300...so what have I got to lose? First, I unplugged the unit. I started by removing the top control box by removing two screws in the back of it. Once off, there are two big clips which hold the body in place. That came off easy. I removed the back next and now had everything out in the open. I disconnected the exit greywater pump which was easy with two snaps. I tipped the unit on the side and removed the motor - also attached with two snap on clips. Between the motor and the gearbox there is a shock absorbing coupler which consist of two white plastic rings with 3 fingers each. These interconnect with a black rubber piece. Once of the white rings was cracked in half and one of the fingers was broken off. So that easy to figure out. I ordered a new coupling on partselect on Friday afternoon. On the next morning, Saturday, Fedex showed up with the replacement part. I was pretty amazed at the fast service since I only paid $7 for ground shipping. Anyway, I put the new coupling on and put the whole thing back together...we've run a dozen loads since without a hiccup. Beats dumpstering the unit or calling a repairman. I spent about an hour to take it apart and about an hour to get it all back together. You definately need a good socket set, screwdrivers. Good luck.

I decided to order the part and attempt to install it. Actually was easy. Took my time and maybe took 90 minutes. Works great.

I read the experiences of others on this site and determined that the problem was probably the lid switch. Used others experience in taking the panel off and removed the old switch and inserted the new one. The post to be sure to have the lid open was good and probably saved me some time. Overall, the fix was simple and the problem appears to have been solved. The lid switch got here the day after I ordered it and that was great service. Better than paying for a service call or new washer.

Watched the video on this site on removal and installment Done in less than 5 minutes including cleaning where the dispenser is located

Hello the installation was real simple I first uplug machine from wall I turn off all water leading to in to the machine I then tip machine on it side I then took loose all wiring leading to the motor then motor is held up with 3 screws and 2 bands that hold it in place I reinstall the new motor coupling insert the wires and turn back on the water leading to machine then plug machine back in, every thing was good to go. . . . Save a lot of money doing it my self so simple to do. . . .

After flipping the washer on it's side snap off the clips that hold the motor in place and discard the old coupling. The new coupling fits in very snug some may need a little persuation to attach but once attached the motor lines up nicely and just snap back the clips, turn the washer over and test with a fresh load.

Raised washer on cinder blocks high enough to get underneath, removed wiring, capacitor (because it got in the way), removed spring clips from pump, removed pump, no water spillage this way. removed clips from motor, removed motor, pulled old broken coupling rubber ring and plastic pieces out, used a spark plug driver to press new ones in place on the gear shaft and motor as they will fit tighter because they have a metal reinforcement that the original did not have, lined up the two halfs and clipped motor back on, cliped pump back on, reconnected wires again, lowered off the blocks and washed a couple loads that night.

I removed four srews holding the control panel and laid it to the side, then removed a screw holding the ground on and disconnected the electrical connection. The lid needs to be open to remove the switch. Just remove the switch and reverse sequence. To replace the coupling , I laid over the washer and removed two screws holding the straps connecting the motor to the transmission. After seperating, I pulled off old couplings and reinstalled the new ones on both the motor and transmission. I had to tap couplings on. Then reversed the installation and set backup and tried it out. It worked great.

i had to strip the outer housing of the wahing machine apart the remove the motoe from the transmission to get to the coupling. once i recived the coupling( which was very quickly) i just reversed those steps.

Turn off the power,remove the washer cabinet top and side panels. unsnap the water pump clips, unscrew and unclip the motor mounting clips.Remove the old drive coupling and triangular drive shaft adaptors.Clean area and install the three new parts, reattach the motor and pump, close the cabinet,turn the power back on and test.Done! The only hard part is working down on the floor and you need a good flashlight.

Unpluged washer. Turned washer on its side, unpluged wire harness to motor. Removed hoses to pump on motor, removed screws and nuts holding motor, then pulled out motor. Popped off old couplings,intalled new, reassembled. Piece of cake!

Unplug washer. Place large old towel in floor at rear of washer. Turn off and disconnect water supply lines and allow to drip dry. Place towel in floor in front of washer. Tip washer forward onto face of washer. Unplug wiring clip connector from drive motor. Remove 2 1/4 inch head screws from spring clips on bottom of motor housing. Slowly rotate clips out of the was to drop motor. Knoch top coupling piece off agitator shaft with screwdriver and light hammer. replace coupling with 5/8 deep well socket as a driver which will fit the metal insert in the coupling and not interfere with the shaft. then drive the other coupling onto the motor shaft using light hammer and drive socket(5/8) deep well. place the rubber shock connector onto the agitator drive piece then slide the motor back into the mount position. rotate the clips vback into place. tighten 1/4 head screws in clips re-attach the wiring harness tip the washer back up onto "feet" re-attach water supply lines tighten appropriately. Plug unit into receptacle and enjoy....