6443B Norge Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Stan from McAllen, TX
- Parts Used:
- 35-2374N
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Water inlet valve not closing.
Disconnected the power plug. Turned off the hot & cold hose water supply. Put down old bath towel. Disconneced hoses from machine inlet valve. Opened entire top for access to electrical connections & fill hose. Replaced inlet valve, new wire connectors. Replaced the hot & cold water hoses.
This was my first washing machine repair.
This was my first washing machine repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from akron, OH
- Parts Used:
- WP21001915
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
water leaking under washer
removed rear acess panel and used pliers to remove leaking hose then reinstalled new hose..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jrrry from Sebree, KY
- Parts Used:
- 35-2374N
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
part received one day after ordering, excellant
took back off washer with nutdriver, pulled wires off by hand, ( was unplugged ). pliars used to remove hose, regular clamp put back on. reinstalled back plugged in, tested water,,,, done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William B from STURGIS, MI
- Parts Used:
- WP21002026, 12002213
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Noisy on spin cycle
Followed the excellent utube instructions you provide. Piece of cake when I followed the video. The rear springs became much more difficult because my model does not have rear access panel. They were the only stuggle. Thank you for doing the repair videos
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bette from S BARRINGTON, IL
- Parts Used:
- WP21001915
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
crack in tub hose causing washer water to spill on to floor
raised the top of the washer to get at the front panel screws. Removed the front panel. Removed the cracked hose and installed the new one. Reinstalled the front and top panels.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen M. from LEWES, DE
- Parts Used:
- WP21001915
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Water leak
Removed front panel by releasing spring clips with putty knife and removed two screws with a ratchet and 5/16” socket. Removed rear access cover with a ratchet and 5/16” socket. Removed and replaced tub to pump hose. Loosened clamps on each end of hose with channel locks.
Re installed rear access cover and front panel.
Re installed rear access cover and front panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Loretta from LEBANON JCT, KY
- Parts Used:
- 12001187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
My 24 year old Maytag performance washer started occasionally not agitating. Eventually it did not agitate at all but would spin.
The lid switch is on the right side top of the washer under the lid. I took a putty knife and found the clips that hold the top of the washer and pushed them to release it. I then lifted it up to fully see the lid switch. I unplugged the washer from the wall socket and took out the 2 screws that holds the lid switch in. Then unplugged the lid switch from its electrical connection and put the new one in its place. Washer is working great so far.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eleanor from PALATKA, FL
- Parts Used:
- 12002213
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Washer was making a squeak during spin cycle & then just stopped spinning
I watched the video of the repair on this website and followed it. Was really easy & THANK GOD because this was my first repair. This has been a great machine and it looks like it will continue to be for a little while longer! Thanks for the video help and friendly navigation of your site!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joe from LAWRENCEVILLE, NJ
- Parts Used:
- 12002213
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Wouldn't spin after rince
Followed the great instructions on your video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny from Fort Worth, TX
- Parts Used:
- WP35-6465
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Drain pump making load screeching noise
I pulled washer out and removed filler hoses from water supply and drain hose and tilted it forward placing three short 2X4's under the washer to keep it tilted forward. Removed
back plate with nutdriver. Removed belt from pulley and disconnected the two hoses from pump with pliers. Removed three large screws from pump base with nutdriver and removed old pump. Installed the new pump in reverse order. Quick and fairly easy took about 30 minutes.
back plate with nutdriver. Removed belt from pulley and disconnected the two hoses from pump with pliers. Removed three large screws from pump base with nutdriver and removed old pump. Installed the new pump in reverse order. Quick and fairly easy took about 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from WINDHAM, NH
- Parts Used:
- WP35-2044
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The top load cover would come off in your hand and it was so loose that the lid cover salety switch would not work
First I got everything I needed, unplugged the washer. Using the puddy knife I freed the top of the washer by inserting the knife about four inches from each side on front. The machine is in a place where it can not be pulled out far, hence the two by fours. Remove the loose cover, reach in with the stubby and unscrew the screw on both sides. Take the broken cover pins off the cover and install the new ones, put the other hinges in the cover, put the hole cover in place and install the one screw perside, remove wood and close the hole top, your in business , no drinking
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angela from FACTORYVILLE, PA
- Parts Used:
- WP35-2044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Hinge Broken
Removed screw, replaced hinge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steve from WATSON, MN
- Parts Used:
- WP21001915
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Tub to pump hose worn out and leaking
Replaced the hose. two clamps and retainers. very basic repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from New London, OH
- Parts Used:
- WP21352320
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old belt broke and fell off
tipped the washer back, laid on the floor, and wrapped new belt around 3 pulleys. everything works as before.
Was this instruction helpful to you?
Thank you for voting!