6530A (REV F) Norge Washer - Instructions

Rolled the old one off and rolled the new one on.

Removed screw, replaced hinge.

I followed your video instructions. Very good video.

First I got everything I needed, unplugged the washer. Using the puddy knife I freed the top of the washer by inserting the knife about four inches from each side on front. The machine is in a place where it can not be pulled out far, hence the two by fours. Remove the loose cover, reach in with the stubby and unscrew the screw on both sides. Take the broken cover pins off the cover and install the new ones, put the other hinges in the cover, put the hole cover in place and install the one screw perside, remove wood and close the hole top, your in business , no drinking

I first changed the belt which helped but it still sounded like it was going to take off through the roof.....I did the pulley and bearing kit in hopes that it would do some good....it went really smoothly with no issues however it did not solve the problem....so it is working and I am going to just ride it out until it quits....thanks

tipped the washer back, laid on the floor, and wrapped new belt around 3 pulleys. everything works as before.

I had my 12 year old son climb to the back and he took off all the screws necessary in the back and took the part completely off. We ordered the part and waited for it to come in. We replaced the part, the screws and honestly, the only thing we had trouble with was replacing the small cover where the hoses stick out of the washer. Was an easy efficient experience that may have saved me $300.00+ dollars. Thanks to my 12 year old son we got her fixed up. The washer works like brand new.

Turned water off,tilted unit forward,removed lower rear cover,removed belt,laid towels around ,removed inlet hose and exit hose off pump,removed 3 screws holding pump,removed pump and installed new one,reversed order of disassemble, has been running great ever since.

My husband unhooked the water lines, unplugged the washer and remove the waste water hose, then we tipped it over and easy as pie the belt came off and the new one went right back on. I did not see any tears or breaks in the old belt, but it was stretched out a bit, and the washer is once again quiet. This also gave me an opportunity to clean under the washer, which we all know we don't do unless we have to. Cheap, quick, and easy fix for someone to do there self.

Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.

Took off belt and ran motor. No noise. Then took off drain pump and spun it by hand and felt rubbing on one spot. I figured the bearings were going bad, so I ordered the parts and replaced them.

Lift the top of the washer so you can access the screws that hold the hinges. Replace the hinges,and close the washer top. This is the sescond time we have had to replace the hinges.

This lid and hinges are very poorly designed. Instead of opening to the side, it opens straight back. That means when the hinges wear out (and they do because they are plastic), you have to push the lid all the way back to stay open. When you push it all the way back, it hits the control knob and turns off the water.

If you are like me, I like to turn the water on and add the soap so it can dissolve before I add the clothes. It is really irritating when you open the lid and the only way for it to stay open is to push it all the way back and the water shuts off. And if you don't push it all the way back, it slams and scares the bejeebers out of you or slams on your fingers.

I unscrewed the old lid switch and screwed on the new switch in seriously 2 minutes!

It was easy to replace the water pump

short drive, 90 degree, "star" driver. push tub to side and back to reach lower part of old hinge, remove single screw. (careful not to drop it into the "mechanics" of the tub.) repeat for the other side. remove parts from lid. reassemble new parts onto lid, along with lower hinge parts. secure the lower hinge to door part(s) with masking tape to hold in place. hold lid in place over lower hinge screw holes and start screws by hand. snug up the screws and your done! the 'STAR" screws may be relpaced with similar "phillips" so you wont have to scrounge for a "star" driver the next time.