6540A (REV K) Norge Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- william from cypress, TX
- Parts Used:
- WP21352320
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
squeel
Tilted machine back, put a paint can under it and did R & R with belts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from New London, OH
- Parts Used:
- WP21352320
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old belt broke and fell off
tipped the washer back, laid on the floor, and wrapped new belt around 3 pulleys. everything works as before.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- loyce from charleston, SC
- Parts Used:
- WP35-2045
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
broken lid hinge
I had my boyfriend take the lid off ,then he took off the two old hinges,one was broken,and the he replaced both lid hinges,daving the good one. it was very simple and quick for him.
Iwill use your service again,thanks.
Loyce Floyd
Iwill use your service again,thanks.
Loyce Floyd
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brandon from Lake Elsinore, CA
- Parts Used:
- WP35-6465
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Water leaked from bottom of Washing Machine.
Removed water lines and drain, removed back panel, removed drain lines from pump. Unscrewed 3 screws to remove pump. attached drain lines to new pump, screwed in new pump, reattached everything. Reinstalled belt (very easy, not like an altenator). done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angela from FACTORYVILLE, PA
- Parts Used:
- WP35-2044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Hinge Broken
Removed screw, replaced hinge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny from Fort Worth, TX
- Parts Used:
- WP35-6465
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Drain pump making load screeching noise
I pulled washer out and removed filler hoses from water supply and drain hose and tilted it forward placing three short 2X4's under the washer to keep it tilted forward. Removed
back plate with nutdriver. Removed belt from pulley and disconnected the two hoses from pump with pliers. Removed three large screws from pump base with nutdriver and removed old pump. Installed the new pump in reverse order. Quick and fairly easy took about 30 minutes.
back plate with nutdriver. Removed belt from pulley and disconnected the two hoses from pump with pliers. Removed three large screws from pump base with nutdriver and removed old pump. Installed the new pump in reverse order. Quick and fairly easy took about 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from WINDHAM, NH
- Parts Used:
- WP35-2044
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The top load cover would come off in your hand and it was so loose that the lid cover salety switch would not work
First I got everything I needed, unplugged the washer. Using the puddy knife I freed the top of the washer by inserting the knife about four inches from each side on front. The machine is in a place where it can not be pulled out far, hence the two by fours. Remove the loose cover, reach in with the stubby and unscrew the screw on both sides. Take the broken cover pins off the cover and install the new ones, put the other hinges in the cover, put the hole cover in place and install the one screw perside, remove wood and close the hole top, your in business , no drinking
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Loretta from LEBANON JCT, KY
- Parts Used:
- 12001187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
My 24 year old Maytag performance washer started occasionally not agitating. Eventually it did not agitate at all but would spin.
The lid switch is on the right side top of the washer under the lid. I took a putty knife and found the clips that hold the top of the washer and pushed them to release it. I then lifted it up to fully see the lid switch. I unplugged the washer from the wall socket and took out the 2 screws that holds the lid switch in. Then unplugged the lid switch from its electrical connection and put the new one in its place. Washer is working great so far.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eleanor from PALATKA, FL
- Parts Used:
- 12002213
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Washer was making a squeak during spin cycle & then just stopped spinning
I watched the video of the repair on this website and followed it. Was really easy & THANK GOD because this was my first repair. This has been a great machine and it looks like it will continue to be for a little while longer! Thanks for the video help and friendly navigation of your site!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joe from LAWRENCEVILLE, NJ
- Parts Used:
- 12002213
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Wouldn't spin after rince
Followed the great instructions on your video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from Elizabeth, NJ
- Parts Used:
- WP35-6465, WP21352320
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Made noise during washing and rinse cycle
It was easy to replace the water pump
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from MEMPHIS, TN
- Parts Used:
- WP89503
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old hot water inlet hose had budge at both ends.
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Les from Moneta, VA
- Parts Used:
- WP35-6465, WP21352320
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Made noise on spin cycle
Took off belt and ran motor. No noise. Then took off drain pump and spun it by hand and felt rubbing on one spot. I figured the bearings were going bad, so I ordered the parts and replaced them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michele from Lebanon, PA
- Parts Used:
- WP35-6465
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Socket set
Started making loud screeching noise(bad Bearing)
Turned water off,tilted unit forward,removed lower rear cover,removed belt,laid towels around ,removed inlet hose and exit hose off pump,removed 3 screws holding pump,removed pump and installed new one,reversed order of disassemble, has been running great ever since.
Was this instruction helpful to you?
Thank you for voting!