Models
>
6375A REV B
6375A REV B Norge Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$5.42
This is a multi-use screw and can be used on a variety of appliances. The measurements of the screw are: 8/18 x 3/8. *Please note: the screw is sold individually. Refer to the manual provided by the m...
In Stock
$11.80
This hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.
In Stock
$7.95
This is a multi-use cover screw. It fits appliances such as dryers, ranges, washers, dishwashers, refrigerators, air conditioners, washer dryer combos, freezers, wall ovens, microwaves, dehumidifiers,...
In Stock
In Stock
In Stock
$57.02
This is part of the lid switch actuator mechanism and activates the lid switch, when the lid is closed, to start the wash cycle and when the lid is open, it stops the cycle.
In Stock
In Stock
In Stock
In Stock
$178.98
This valve has two ports for water to enter. It also comes with a metallic hose clamp.
In Stock
In Stock
$93.67
This valve has two ports for water to enter. This valve is compatible with a half inch ID hose and it has two 3/4-11x1/2 NHT hose threads.
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 6375A REV B
Viewing 5 of 5Leaking
Fixed by these parts
How to fix it
No hot or cold water
Fixed by these parts
How to fix it
Will not drain
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Will not agitate
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Linda from La Porte, IN
- Parts Used:
- 12001187
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Intermittent problem with lid switch, no high speed spin/pump out
Disconnect power, unsnap and raise machine top cover w/lid, remove old switch - two screws under lid, taking care to not drop loose actuator lever into machine. Remove control panel back and disconnect switch wire connector. Intall new switch, taking care to not drop loose actuator lever into machine, connect switch wires inside control
... Read more
panel. Replace panel cover and lower machine top cover w/lid and snap into place, reconnect power, verify operation...
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Chester, NJ
- Parts Used:
- 358277
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Replacement of the water inlet vaqlve
First I disconnected the inlet hoses. After lifting up the cover the electrical wires were marked and disconnected from the old valve. Next the short hose from the old valve to the tub was removed. Then the old valve was removed from the washing machine by removal of two mounting screws. The new valve was installed in the reverse orde
... Read more
r. New hose clamps were installed on the short hose from the valve to the tub. New washers were installed on the hoses which connected to the valve. A test was made to check for any leaks.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Rochester, NY
- Parts Used:
- WP43-0057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lid switch had deteriated over time and no longer made contact
removed the screw holding the actuator, ordered the new part and replaced it when it arrived. Shipping was really fast and I even received it one day early.
Was this instruction helpful to you?
Thank you for voting!