6530A REV D Norge Washer - Instructions

used putty knife to to raise the top, took out two screws, replaced parts , then closed the top.

removed hoses and belt. removed 3 screws that secured pump. and then removed pump. received new pump and just reversed the process to repair!

UNPLUG ELECTRICITY. I pulled out the washing machine turned the water off pulled all of your hoses from the back of the machine there may be a mess so you need some thing that will catch the water as it comes out of the hoses. On the bottom of the machine is a belt you have to remove it. Its easy just pull it off. On the back is a panel that you unscrew four screws. On the water pump it self you unscrew three screws. Then for the new part you do in reverse order screw your three screws back in put your hoses back on make sure your clamps are tight around your hoses or you will have a leak. Put your panel back on. Put your belt back on. Turn your water on from the wall plug in the electricity and you are done.

Opened hinges top of washer. Removed screws holding hinge bases. Removed the washer top lid and unscrewd broken hinge pin. Replaced hinge pin and inserted in pin base and screwd base op hinge back onto washer and job was done.

I followed the feed back in the forum from a previous repair. I popped open the top of the Washing and propped it open @ approx. 70 degrees,moved the Tub out of the way and used a small Phillips Scwdrvr to remove the broken part, installing the new parts was a snap, I took the time to use a Q-Tip and petroleum jelly to coat the pin and hinge making it easier and less binding when opening the lid.

Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.

Unscrewed the front panel. Then took pump out & put new one in. . . . . Thank you part select. Com. . . Super fast shipping. . .

Lift the top of the washer so you can access the screws that hold the hinges. Replace the hinges,and close the washer top. This is the sescond time we have had to replace the hinges.

This lid and hinges are very poorly designed. Instead of opening to the side, it opens straight back. That means when the hinges wear out (and they do because they are plastic), you have to push the lid all the way back to stay open. When you push it all the way back, it hits the control knob and turns off the water.

If you are like me, I like to turn the water on and add the soap so it can dissolve before I add the clothes. It is really irritating when you open the lid and the only way for it to stay open is to push it all the way back and the water shuts off. And if you don't push it all the way back, it slams and scares the bejeebers out of you or slams on your fingers.

Turned water off,tilted unit forward,removed lower rear cover,removed belt,laid towels around ,removed inlet hose and exit hose off pump,removed 3 screws holding pump,removed pump and installed new one,reversed order of disassemble, has been running great ever since.

My husband unhooked the water lines, unplugged the washer and remove the waste water hose, then we tipped it over and easy as pie the belt came off and the new one went right back on. I did not see any tears or breaks in the old belt, but it was stretched out a bit, and the washer is once again quiet. This also gave me an opportunity to clean under the washer, which we all know we don't do unless we have to. Cheap, quick, and easy fix for someone to do there self.

Took off belt and ran motor. No noise. Then took off drain pump and spun it by hand and felt rubbing on one spot. I figured the bearings were going bad, so I ordered the parts and replaced them.

It was easy to replace the water pump

changed drive belt and saved me from buying new washer,,working like bland new again ...many thanks

short drive, 90 degree, "star" driver. push tub to side and back to reach lower part of old hinge, remove single screw. (careful not to drop it into the "mechanics" of the tub.) repeat for the other side. remove parts from lid. reassemble new parts onto lid, along with lower hinge parts. secure the lower hinge to door part(s) with masking tape to hold in place. hold lid in place over lower hinge screw holes and start screws by hand. snug up the screws and your done! the 'STAR" screws may be relpaced with similar "phillips" so you wont have to scrounge for a "star" driver the next time.

I followed Gary from Sioux City IA instructions. Very well explained.