GA108 Maytag Washer - Instructions

Could not repair. The gearbox on the agitator was broken and that kept the agitator from working. Do not assume it is a belt problem on a washer built in 1987.

There are two screws that hold the switch in place. And two wires connected to the switch. The most difficult part of replacement is to place the new switch and hold it in place to reinstall the mounting screws. The space to work in is limited unless you remove the front panel from the dryer, which I opted not to do.

Layed the machine on it'sback and put the 2 belts on the pulleys,Very easy ,when you know to put the machine on it's backside!

The repair itself is fairly simple. However, being 65 years old getting the new valve back into the back opening of the washer and screwed in was a challenge. The clamp on the water connector hose broke and I had to drive to the store to replace it. You may want to consider giving a heads-ups option of ordering hose clamps to DIYers, when you go to order. Also, the instructions that came with the part was not totally accurate. I had to rotate the cylinders outward to connect to the electrical points. But, my machine is pretty old and that may be why. Otherwise, I am very pleased with how quick I received the part and it was exactly what I ordered. My washing machine is back in business. Thank you

To troubleshoot the problem I removed a panel/blank from the back of the machine. I then started to fill the tub while watching the pump. It immediately leaked from the shaft seal. I ordered the part early the next morning. It arrived late the next day. I was able to remove the front panel of the machine by removing a screw at each front corner of the bottom of the machine. The pump was attached with three screws which were simple to remove. The pump was an exact replacement and fit identically to the original. I tensioned the belt, and tested the machine. Before reinstalling the front cover, I cleaned the interior of the machine a bit and replaced a couple of hose clamps whose steel screws had started to corrode. All in all a simple repair.

The replacement of the Water Inlet Valve supplied by PartSelect (model PS60378) was too easy.
The key issue was to remove previously the whole upper cover of the washer machine, including the Control Panel, and disconnect all the cables from the electronic Control Board, in order to work easy and freely to remove the inner water hose that is connected to the water inlet valve, working from inside and not from outside of the machine.
Care must be taken writing a notepad of the position of every cable, for not making mistakes when reconnecting them to the Control Panel.

My Maytag A308 is about 25 yrs old and has been filling by a trickle for a while - both hot and cold. I replaced the water valve and that fixed the hot. Cold still running slow. I switched the hoses, thinking one might be clogged, and determined that the cold shut-off was clogged. I replaced that with a ball-valve - about $10 - and it works like it used to. My advice to anyone who installs a shut-off to any fixture - sink, toilet, w-machine, etc - NOT to use a cheap washer-type valve - they tend to freeze up over time and do not close when needed. Same for clean-out drain on hot water heaters.

Water valve on the A308 was accessible and easy to replace. Required rotation of solenoids was easy and connections were obvious. PartSelect
pictures were very useful and price was better than other on-line sources.

Ron

I tipped the washer up on 2by4 blocks used 1/4 inch rachet with 5/16 socket two remove 3 screws and the belt from underneath. Took clamps off hoses yahoo saved l00 bucks!

Followed video that came with part.

I tipped the washing machine (somewhat tricky since it sits under the dryer) and saw the broken belt. Went online, found the belt I needed, bought the set of two belts since I figured it would probably be a good idea to change both belts at the same time. After a few days I had the belts in hand; it took more time to jockey the machine back into place than it did to attach the belts. No tools necessary; the washer parts are on a spring. I did need a screwdriver, however, just to re-attach the washer's front panel.

Found main drive belt had a big chunk out of it. Both belts were worn and "gummy". Replaced both belts with belt kit 12112425; no tools needed -- belts are replaced from the bottom. Just tip the washer back to the wall, and there are the belts.. Installation time 5 minutes.

removed cover, disconnected small water tube and disconnected electrical connections. Reversed above to install new piece. two nutdrivers required. Channel locks for supply hoses.

new replacement water pump leaked where plastic housing upper and lower halves were bonded, presumably with glue. As a quick fix I wrapped pump with some 3M 4411N sealing tape. Seems to have stopped or really slowed leak. I was going to get another new pump but now worried it will leak as well so going to see how long tape fix works..

I order a water inlet valve from this site It was the best buy around. The email from the site part came with a video how to change it. It was a 15 minute job. One 5/16 nut driver to remove the inlet valve and pliers to remove the hoes from the valve. Easy off easy on.

Watched your video and followed your instructions and it was very simple.We bought our maytag washer in 1988 next year it will be 30 years old we raised 3 children and for $21 and your video I hope to it last another 30 years